• melnikdima
  • Посетитель
  • Неактивен
  • Зарегистрирован: 24.02.2010
  • Сообщений: 7
  • Репутация : [ 0 | 0 ]

ребят мож кто сталкивался???

/usr/sbin/hddtemp /dev/sda*

/dev/sda: Maxtor 2B010H1: 0°C
/dev/sda1: Maxtor 2B010H1: 0°C
/dev/sda2: Maxtor 2B010H1: 0°C
/dev/sda5: Maxtor 2B010H1: 0°C


установил прогу hdsentinel


вот что она выдаёт!!!

root@dascha-serv:~# sudo ./hdsentinel
Hard Disk Sentinel for LINUX console 0.03 (c) 2008-2009 info@hdsentinel.com
Start with -r [reportfile] to save data to report, -h for help

Examining hard disk configuration ...

HDD Device  0: /dev/sda
HDD Model ID : Maxtor 2B010H1
HDD Serial No: B18SWD7E
HDD Revision : WAK21R90
HDD Size     : 9772 MB
Interface    : IDE/ATA
Temperature  : Unknown °C
Health       : 100 %
Performance  : 70 %
Power on time: 53 days, 7 hours, 58 minutes
Est. lifetime: more than 1000 days

Temperature  : Unknown °C


что hddtemp не определяет температуру что и эта прога не определяет!!! куда рыть????

2 Ответ от Lupo Alberto (06.09.2010 00:25:22 отредактировано Lupo Alberto)

  • Откуда: Беларусь, Гомель
  • Зарегистрирован: 04.07.2010
  • Сообщений: 11,183
  • Репутация : [ 571 | 8 ]

hddtemp определяет температуру только тех дисков, сведения о которых есть в её базе данных.
Есть несколько способов решить вашу проблему:
1. Малореальный — обновить базу данных программы (см. man hddtemp) и надеяться, что сведения о вашем диске уже появились;
2. Практический — воспользоваться командой вида

smartctl -a /dev/sda | grep -i temperature | awk '{print $10}'


3. Правильный — используя данные, предоставляемые командой smartctl дополнить существующий файл базы данных дисков либо создать собственный, который и указывать при вызове hddtemp. Покажите вывод команды

smartctl -a /dev/sda | egrep 'Device Mode|Model Family|Temperature'
Был, был и весь вышел...

3 Ответ от melnikdima (06.09.2010 00:30:41 отредактировано melnikdima)

  • melnikdima
  • Посетитель
  • Неактивен
  • Зарегистрирован: 24.02.2010
  • Сообщений: 7
  • Репутация : [ 0 | 0 ]

вот что вывел...

температуры и не видно....

mel@dascha-serv:~$ sudo smartctl -a /dev/sda
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Model Family:     Maxtor Fireball 541DX family
Device Model:     Maxtor 2B010H1
Serial Number:    B18SWD7E
Firmware Version: WAK21R90
User Capacity:    10 246 569 984 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   7
ATA Standard is:  ATA/ATAPI-7 T13 1532D revision 0
Local Time is:    Mon Sep  6 00:27:45 2010 MSD
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever 
                                        been run.
Total time to complete Offline 
data collection:                 (  30) seconds.
Offline data collection
capabilities:                    (0x1b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        No Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        No General Purpose Logging support.
Short self-test routine 
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        (  13) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  3 Spin_Up_Time            0x0027   234   233   063    Pre-fail  Always       -       4675
  4 Start_Stop_Count        0x0032   253   253   000    Old_age   Always       -       359
  5 Reallocated_Sector_Ct   0x0033   253   253   063    Pre-fail  Always       -       0
  6 Read_Channel_Margin     0x0001   253   253   100    Pre-fail  Offline      -       0
  7 Seek_Error_Rate         0x000a   253   252   000    Old_age   Always       -       0
  8 Seek_Time_Performance   0x0027   248   245   187    Pre-fail  Always       -       34378
  9 Power_On_Minutes        0x0032   250   250   000    Old_age   Always       -       187h+42m
 10 Spin_Retry_Count        0x002b   253   252   157    Pre-fail  Always       -       0
 11 Calibration_Retry_Count 0x002b   253   252   223    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   249   249   000    Old_age   Always       -       1747
192 Power-Off_Retract_Count 0x0032   253   253   000    Old_age   Always       -       85
193 Load_Cycle_Count        0x0032   253   253   000    Old_age   Always       -       976
194 Unknown_Attribute       0x0032   253   253   000    Old_age   Always       -       0
195 Hardware_ECC_Recovered  0x000a   253   252   000    Old_age   Always       -       133
196 Reallocated_Event_Count 0x0008   253   253   000    Old_age   Offline      -       0
197 Current_Pending_Sector  0x0008   253   253   000    Old_age   Offline      -       0
198 Offline_Uncorrectable   0x0008   253   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0008   199   199   000    Old_age   Offline      -       0
200 Multi_Zone_Error_Rate   0x000a   253   252   000    Old_age   Always       -       0
201 Soft_Read_Error_Rate    0x000a   253   249   000    Old_age   Always       -       354
202 TA_Increase_Count       0x000a   253   252   000    Old_age   Always       -       0
203 Run_Out_Cancel          0x000b   253   252   180    Pre-fail  Always       -       0
204 Shock_Count_Write_Opern 0x000a   253   252   000    Old_age   Always       -       0
205 Shock_Rate_Write_Opern  0x000a   253   252   000    Old_age   Always       -       0
207 Spin_High_Current       0x002a   253   252   000    Old_age   Always       -       0
208 Spin_Buzz               0x002a   253   252   000    Old_age   Always       -       0
209 Offline_Seek_Performnce 0x0024   253   253   000    Old_age   Offline      -       0
 99 Unknown_Attribute       0x0004   253   253   000    Old_age   Offline      -       0
100 Unknown_Attribute       0x0004   253   253   000    Old_age   Offline      -       0
101 Unknown_Attribute       0x0004   253   253   000    Old_age   Offline      -       0

SMART Error Log Version: 1
Warning: ATA error count 3619 inconsistent with error log pointer 5

ATA Error Count: 3619 (device log contains only the most recent five errors)
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 3619 occurred at disk power-on lifetime: 1195 hours (49 days + 19 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 51 00 00 00 00 a0  Error: ABRT

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  a1 00 00 00 00 00 a0 00      00:03:36.880  IDENTIFY PACKET DEVICE
  25 00 01 01 00 00 e0 08      00:03:32.528  READ DMA EXT
  25 00 01 00 00 00 e0 08      00:03:32.528  READ DMA EXT
  25 00 01 00 00 00 e0 08      00:03:32.496  READ DMA EXT
  c6 00 10 00 00 00 ef 08      00:03:31.952  SET MULTIPLE MODE

Error 3618 occurred at disk power-on lifetime: 1195 hours (49 days + 19 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 51 01 3e c5 fa 80

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  f5 00 01 3e c5 fa 80 08      00:03:31.808  SECURITY FREEZE LOCK
  42 00 01 3e c5 fa e0 08      00:03:30.960  READ VERIFY SECTOR(S) EXT
  e3 00 00 01 00 00 a0 08      00:03:29.936  IDLE
  c8 00 01 01 00 00 a0 08      00:03:29.936  READ DMA
  ef 03 45 01 4f c2 a0 08      00:03:29.920  SET FEATURES [Set transfer mode]

Error 3617 occurred at disk power-on lifetime: 1195 hours (49 days + 19 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 51 01 3e c5 fa 80

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  f5 00 01 3e c5 fa 80 08      00:02:25.664  SECURITY FREEZE LOCK
  42 00 01 3e c5 fa e0 08      00:02:24.848  READ VERIFY SECTOR(S) EXT
  e3 00 00 01 00 00 a0 08      00:02:23.824  IDLE
  c8 00 01 01 00 00 a0 08      00:02:23.824  READ DMA
  ef 03 45 01 4f c2 a0 08      00:02:23.808  SET FEATURES [Set transfer mode]

Error 3616 occurred at disk power-on lifetime: 1195 hours (49 days + 19 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 51 00 3e c5 fa 80

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  f5 00 00 3e c5 fa 80 08      00:02:25.536  SECURITY FREEZE LOCK
  42 00 01 3e c5 fa e0 08      00:02:24.832  READ VERIFY SECTOR(S) EXT
  e3 00 00 01 00 00 a0 08      00:02:23.808  IDLE
  c8 00 01 01 00 00 a0 08      00:02:23.808  READ DMA
  ef 03 45 01 4f c2 a0 08      00:02:23.808  SET FEATURES [Set transfer mode]

Error 3615 occurred at disk power-on lifetime: 1194 hours (49 days + 18 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 51 01 3e c5 fa 80

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  f5 00 01 3e c5 fa 80 08      00:02:25.824  SECURITY FREEZE LOCK
  42 00 01 3e c5 fa e0 08      00:02:25.232  READ VERIFY SECTOR(S) EXT
  e3 00 00 01 00 00 a0 08      00:02:24.208  IDLE
  c8 00 01 01 00 00 a0 08      00:02:24.208  READ DMA
  ef 03 45 01 4f c2 a0 08      00:02:24.192  SET FEATURES [Set transfer mode]

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


Device does not support Selective Self Tests/Logging

4 Ответ от melnikdima

  • melnikdima
  • Посетитель
  • Неактивен
  • Зарегистрирован: 24.02.2010
  • Сообщений: 7
  • Репутация : [ 0 | 0 ]

проблема решена у Maxtor 2B010H1 нет датчика температуры!!!!!!!!!!!!!!!!!!! заразы!!!

спс Lupo Alberto что хотел помочь)

5 Ответ от Lupo Alberto

  • Откуда: Беларусь, Гомель
  • Зарегистрирован: 04.07.2010
  • Сообщений: 11,183
  • Репутация : [ 571 | 8 ]

Какой-то «интересный» у вас диск:

grep 'Maxtor Fireball 541DX' /usr/share/hddtemp/hddtemp.db
#"Maxtor 2B0[012][04568]H1"                ???  C    "Maxtor Fireball 541DX"

В базе данных сведения о нём закомментированы, на месте температуры — вопросики  oO

Был, был и весь вышел...