Linux Forum — openSUSE 12.3 x86_64 и Черный экран вместо ttyX. GRUB или fglrx?

Re: openSUSE 12.3 x86_64 и Черный экран вместо ttyX. GRUB или fglrx?

null@example.com (sandaksatru) — Wed, 06 Nov 2013 14:59:54 +0000

Nyan Kitty Fungus пишет:

sandaksatru, это оно, спаибо за помощь

Всегда пожалуйста! Кстати, сам сегодня столкнулся с подобной проблемой только на другом железе и с другим драйвером, и на поиск решения тратить время уже не пришлось Вот что значит вовремя разобраться в чужой проблеме )))

Re: openSUSE 12.3 x86_64 и Черный экран вместо ttyX. GRUB или fglrx?

null@example.com (Nyan Kitty Fungus) — Wed, 06 Nov 2013 12:33:41 +0000

sandaksatru, это оно, спаибо за помощь

Re: openSUSE 12.3 x86_64 и Черный экран вместо ttyX. GRUB или fglrx?

null@example.com (sandaksatru) — Tue, 05 Nov 2013 23:49:48 +0000

Nyan Kitty Fungus пишет:

+ открыть спойлер
GRUB_TERMINAL=console
# The resolution used on graphical terminal
# note that you can use only modes which your graphic card supports via VBE
# you can see them in real GRUB with the command `vbeinfo'
GRUB_GFXMODE=auto

Если у вас параметры GRUB_TERMINAL и GRUB_GFXMODE были раскомментированы, попробуйте закомментировать (но, если честно, я не уверен в этом ли дело):

#GRUB_TERMINAL=console
# The resolution used on graphical terminal
# note that you can use only modes which your graphic card supports via VBE
# you can see them in real GRUB with the command `vbeinfo'
#GRUB_GFXMODE=auto

После этого не забудьте обновить:

grub2-mkconfig -o /boot/grub2/grub.cfg

Re: openSUSE 12.3 x86_64 и Черный экран вместо ttyX. GRUB или fglrx?

null@example.com (Nyan Kitty Fungus) — Tue, 05 Nov 2013 23:03:45 +0000

+ /etc/default/grub

# Modified by YaST2. Last modification on Ср ноя  6 01:30:56 FET 2013
# THIS FILE WILL BE PARTIALLY OVERWRITTEN by perl-Bootloader
# For the new kernel it try to figure out old parameters. In case we are not able to recognize it (e.g. change of flavor or strange install order ) it it use as fallback installation parameters from /etc/sysconfig/bootloader

# If you change this file, run 'grub2-mkconfig -o /boot/grub2/grub.cfg' afterwards to update
# /boot/grub2/grub.cfg.
GRUB_DISTRIBUTOR="openSUSE 12.3"
GRUB_DEFAULT=saved
GRUB_HIDDEN_TIMEOUT=0
GRUB_HIDDEN_TIMEOUT_QUIET=true
GRUB_TIMEOUT=3
GRUB_CMDLINE_LINUX_DEFAULT=" resume=/dev/sdb1 splash=silent quiet radeon.modeset=0 showopts"
# kernel command line options for failsafe mode
GRUB_CMDLINE_LINUX_RECOVERY="showopts apm=off noresume edd=off powersaved=off nohz=off highres=off processor.max_cstate=1 nomodeset x11failsafe"
GRUB_CMDLINE_LINUX=""
# Uncomment to enable BadRAM filtering, modify to suit your needs
# This works with Linux (no patch required) and with any kernel that obtains
# the memory map information from GRUB (GNU Mach, kernel of FreeBSD ...)
#GRUB_BADRAM=0x01234567,0xfefefefe,0x89abcdef,0xefefefef
# Uncomment to disable graphical terminal (grub-pc only)
GRUB_TERMINAL=console
# The resolution used on graphical terminal
# note that you can use only modes which your graphic card supports via VBE
# you can see them in real GRUB with the command `vbeinfo'
GRUB_GFXMODE=auto
# Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux
#GRUB_DISABLE_LINUX_UUID=true
# Uncomment to disable generation of recovery mode menu entries
#GRUB_DISABLE_LINUX_RECOVERY=true
# Uncomment to get a beep at grub start
#GRUB_INIT_TUNE="480 440 1"
# Skip 30_os-prober if you experienced very slow in probing them
# WARNING foregin OS menu entries will be lost if set true here
GRUB_DISABLE_OS_PROBER=true
GRUB_THEME=/boot/grub2/themes/openSUSE/theme.txt
GRUB_BACKGROUND=/boot/grub2/themes/openSUSE/background.png

Re: openSUSE 12.3 x86_64 и Черный экран вместо ttyX. GRUB или fglrx?

null@example.com (sandaksatru) — Tue, 05 Nov 2013 22:58:18 +0000

Nyan Kitty Fungus пишет:

Вместо tty[1-6] чёрный экран, но ctrl-alt-F* работает и на ввод с клавиатуры реагирует (проверил вслепую)

Может быть дело в графическом терминале?

cat /etc/default/grub

# Uncomment to disable graphical terminal (grub-pc only)
#GRUB_TERMINAL=console
# The resolution used on graphical terminal
# note that you can use only modes which your graphic card supports via VBE
# you can see them in real GRUB with the command `vbeinfo'
#GRUB_GFXMODE=640x480

openSUSE 12.3 x86_64 и Черный экран вместо ttyX. GRUB или fglrx?

null@example.com (Nyan Kitty Fungus) — Tue, 05 Nov 2013 22:46:10 +0000

Вместо tty[1-6] чёрный экран, но ctrl-alt-F* работает и на ввод с клавиатуры реагирует (проверил вслепую)
Иксы же работают нормально

Видеокарта Radeon HD7790, установлен самособранный fglrx (ручная сборка и установка)
Загрузчик GRUB2

+ /boot/grub2/grub.cfg

#
# DO NOT EDIT THIS FILE
#
# It is automatically generated by grub2-mkconfig using templates
# from /etc/grub.d and settings from /etc/default/grub
#

### BEGIN /etc/grub.d/00_header ###
if [ -s $prefix/grubenv ]; then
  load_env
fi
set default="${saved_entry}"

if [ x"${feature_menuentry_id}" = xy ]; then
  menuentry_id_option="--id"
else
  menuentry_id_option=""
fi                                                                                                                                                               
                                                                                                                                                                 
export menuentry_id_option                                                                                                                                       
                                                                                                                                                                 
if [ "${prev_saved_entry}" ]; then                                                                                                                               
  set saved_entry="${prev_saved_entry}"                                                                                                                          
  save_env saved_entry                                                                                                                                           
  set prev_saved_entry=                                                                                                                                          
  save_env prev_saved_entry                                                                                                                                      
  set boot_once=true                                                                                                                                             
fi                                                                                                                                                               
                                                                                                                                                                 
function savedefault {                                                                                                                                           
  if [ -z "${boot_once}" ]; then                                                                                                                                 
    saved_entry="${chosen}"                                                                                                                                      
    save_env saved_entry                                                                                                                                         
  fi
}

function load_video {
  if [ x$feature_all_video_module = xy ]; then
    insmod all_video
  else
    insmod efi_gop
    insmod efi_uga
    insmod ieee1275_fb
    insmod vbe
    insmod vga
    insmod video_bochs
    insmod video_cirrus
  fi
}

terminal_input console
terminal_output console
if [ x${boot_once} = xtrue ]; then
  set timeout=0
elif sleep --interruptible 0 ; then
  set timeout=3
fi
### END /etc/grub.d/00_header ###

### BEGIN /etc/grub.d/10_linux ###
menuentry 'openSUSE 12.3' --class 'opensuse-12-3' --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-simple-cda331b9-0545-45b3-8c57-9401d32283bb' {
        load_video
        set gfxpayload=keep
        insmod gzio
        insmod part_msdos
        insmod ext2
        set root='hd1,msdos5'
        if [ x$feature_platform_search_hint = xy ]; then
          search --no-floppy --fs-uuid --set=root --hint-bios=hd1,msdos5 --hint-efi=hd1,msdos5 --hint-baremetal=ahci1,msdos5 --hint='hd1,msdos5'  573af1d2-0540-4195-b5ba-596b34eceb0d
        else
          search --no-floppy --fs-uuid --set=root 573af1d2-0540-4195-b5ba-596b34eceb0d
        fi
        echo    'Loading Linux 3.7.10-1.16-desktop ...'
        linux   /vmlinuz-3.7.10-1.16-desktop root=UUID=cda331b9-0545-45b3-8c57-9401d32283bb   resume=/dev/sdb1 splash=silent quiet radeon.modeset=0 showopts
        echo    'Loading initial ramdisk ...'
        initrd  /initrd-3.7.10-1.16-desktop
}
submenu 'Advanced options for openSUSE 12.3' $menuentry_id_option 'gnulinux-advanced-cda331b9-0545-45b3-8c57-9401d32283bb' {
        menuentry 'openSUSE 12.3, with Linux 3.7.10-1.16-desktop' --class 'opensuse-12-3' --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.7.10-1.16-desktop-advanced-cda331b9-0545-45b3-8c57-9401d32283bb' {
                load_video
                set gfxpayload=keep
                insmod gzio
                insmod part_msdos
                insmod ext2
                set root='hd1,msdos5'
                if [ x$feature_platform_search_hint = xy ]; then
                  search --no-floppy --fs-uuid --set=root --hint-bios=hd1,msdos5 --hint-efi=hd1,msdos5 --hint-baremetal=ahci1,msdos5 --hint='hd1,msdos5'  573af1d2-0540-4195-b5ba-596b34eceb0d
                else
                  search --no-floppy --fs-uuid --set=root 573af1d2-0540-4195-b5ba-596b34eceb0d
                fi
                echo    'Loading Linux 3.7.10-1.16-desktop ...'
                linux   /vmlinuz-3.7.10-1.16-desktop root=UUID=cda331b9-0545-45b3-8c57-9401d32283bb   resume=/dev/sdb1 splash=silent quiet radeon.modeset=0 showopts
                echo    'Loading initial ramdisk ...'
                initrd  /initrd-3.7.10-1.16-desktop
        }
        menuentry 'openSUSE 12.3, with Linux 3.7.10-1.16-desktop (recovery mode)' --class 'opensuse-12-3' --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.7.10-1.16-desktop-recovery-cda331b9-0545-45b3-8c57-9401d32283bb' {
                load_video
                set gfxpayload=keep
                insmod gzio
                insmod part_msdos
                insmod ext2
                set root='hd1,msdos5'
                if [ x$feature_platform_search_hint = xy ]; then
                  search --no-floppy --fs-uuid --set=root --hint-bios=hd1,msdos5 --hint-efi=hd1,msdos5 --hint-baremetal=ahci1,msdos5 --hint='hd1,msdos5'  573af1d2-0540-4195-b5ba-596b34eceb0d
                else
                  search --no-floppy --fs-uuid --set=root 573af1d2-0540-4195-b5ba-596b34eceb0d
                fi
                echo    'Loading Linux 3.7.10-1.16-desktop ...'
                linux   /vmlinuz-3.7.10-1.16-desktop root=UUID=cda331b9-0545-45b3-8c57-9401d32283bb  showopts apm=off noresume edd=off powersaved=off nohz=off highres=off processor.max_cstate=1 nomodeset x11failsafe
                echo    'Loading initial ramdisk ...'
                initrd  /initrd-3.7.10-1.16-desktop
        }
}

### END /etc/grub.d/10_linux ###

### BEGIN /etc/grub.d/20_linux_xen ###
### END /etc/grub.d/20_linux_xen ###

### BEGIN /etc/grub.d/20_memtest86+ ###
menuentry 'openSUSE 12.3 Memtest' --class opensuse --class memtest86 --class gnu --class tools $menuentry_id_option 'memtest-573af1d2-0540-4195-b5ba-596b34eceb0d' {
        insmod part_msdos
        insmod ext2
        set root='hd1,msdos5'
        if [ x$feature_platform_search_hint = xy ]; then
          search --no-floppy --fs-uuid --set=root --hint-bios=hd1,msdos5 --hint-efi=hd1,msdos5 --hint-baremetal=ahci1,msdos5 --hint='hd1,msdos5'  573af1d2-0540-4195-b5ba-596b34eceb0d
        else
          search --no-floppy --fs-uuid --set=root 573af1d2-0540-4195-b5ba-596b34eceb0d
        fi
        echo    'Loading memtest ...'
        linux16 /memtest.bin
}
### END /etc/grub.d/20_memtest86+ ###

### BEGIN /etc/grub.d/20_ppc_terminfo ###
### END /etc/grub.d/20_ppc_terminfo ###

### BEGIN /etc/grub.d/30_os-prober ###
### END /etc/grub.d/30_os-prober ###

### BEGIN /etc/grub.d/40_custom ###
# This file provides an easy way to add custom menu entries.  Simply type the
# menu entries you want to add after this comment.  Be careful not to change
# the 'exec tail' line above.
### END /etc/grub.d/40_custom ###

### BEGIN /etc/grub.d/41_custom ###
if [ -f  ${config_directory}/custom.cfg ]; then
  source ${config_directory}/custom.cfg
elif [ -z "${config_directory}" -a -f  $prefix/custom.cfg ]; then
  source $prefix/custom.cfg;
fi
### END /etc/grub.d/41_custom ###

### BEGIN /etc/grub.d/90_persistent ###
### END /etc/grub.d/90_persistent ###

Монитор -- LG-не помню-какой 1280х1024 60-75 МГц

Как вернуть tty* в нормальное состояние?