Здравствуйте,
Собственно, оказалось, что это не 3G а модем с gsm
kppp не увидел модема
Сейчас пробую wvdial, но постоянно получаю " Modem not responding."
# dmesg | grep tty
console [tty0] enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
# wvdialconf /etc/wvdial.conf
Editing `/etc/wvdial.conf'.
Scanning your serial ports for a modem.
ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Modem Port Scan<*1>: S2 S3
WvModem<*1>: Cannot get information for serial port.
ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud
ttyUSB0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
WvModem<*1>: Cannot get information for serial port.
ttyUSB1<*1>: ATQ0 V1 E1 -- OK
ttyUSB1<*1>: ATQ0 V1 E1 Z -- OK
ttyUSB1<*1>: ATQ0 V1 E1 S0=0 -- ERROR
ttyUSB1<*1>: ATQ0 V1 E1 &C1 -- ERROR
ttyUSB1<*1>: ATQ0 V1 E1 &D2 -- ERROR
ttyUSB1<*1>: ATQ0 V1 E1 +FCLASS=0 -- OK
ttyUSB1<*1>: Modem Identifier: ATI -- Manufacturer: ZTE CORPORATION
ttyUSB1<*1>: Speed 9600: AT -- OK
ttyUSB1<*1>: Max speed is 9600; that should be safe.
ttyUSB1<*1>: ATQ0 V1 E1 +FCLASS=0 -- OK
WvModem<*1>: Cannot get information for serial port.
ttyUSB2<*1>: ATQ0 V1 E1 -- OK
ttyUSB2<*1>: ATQ0 V1 E1 Z -- OK
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 -- ERROR
ttyUSB2<*1>: ATQ0 V1 E1 &C1 -- ERROR
ttyUSB2<*1>: ATQ0 V1 E1 &D2 -- ERROR
ttyUSB2<*1>: ATQ0 V1 E1 +FCLASS=0 -- OK
ttyUSB2<*1>: Modem Identifier: ATI -- Manufacturer: ZTE CORPORATION
ttyUSB2<*1>: Speed 9600: AT -- OK
ttyUSB2<*1>: Max speed is 9600; that should be safe.
ttyUSB2<*1>: ATQ0 V1 E1 +FCLASS=0 -- OK
Found a modem on /dev/ttyUSB1.
Modem configuration written to /etc/wvdial.conf.
ttyUSB1<Info>: Speed 9600; init "ATQ0 V1 E1 +FCLASS=0"
Конфиг wvdial
/etc/wvdial.conf
[Dialer Defaults]
Init1 = AT+CGDCONT=1,"IP","www.ab.kyivstar.net"
Init2 = ATQ0 V1 E1 +FCLASS=0
Init3 = ATZ
Modem Type = USB Modem
Phone = *99#
ISDN = 0
Username =
Password =
Modem = /dev/ttyUSB0
Baud = 9600
wvdial
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: AT+CGDCONT=1,"IP","www.ab.kyivstar.net"
--> Sending: ATQ0
--> Re-Sending: AT+CGDCONT=1,"IP","www.ab.kyivstar.net"
--> Modem not responding.
