Настоятельно просим вас при общении соблюдать Правила форума и законы РФ. Наша тематика вне политики, поэтому воздержитесь от обсуждения ситуации на Украине и связанных с ней событий, независимо от того, какую сторону вы поддерживаете.
Также напоминаем, что наш форум находится в доменной зоне .ru, физически расположен на российских серверах и мы соблюдаем действующее законодательство России. Любые сообщения о политике будут удаляться.
Linux Forum → Ubuntu, Linux Mint → samsung NP-N145 соединение по вайфай
Страницы 1
Чтобы отправить ответ, вы должны войти или зарегистрироваться
столкнулся с проблемой на Ubuntu 10.04 по подключению вафли.
установил Ubuntu 10.04 на нетбук интернет работает только от кабеля. Лампочка горит что вафля включена но ни поиска ничего не происходит. такое впечатление что он выключен, или сломался. подскажите как через консоль это все проверить или подключить.
в настройке подключения показано что есть только проводное соединение, а беспроводного нет.
Включается это в сочетании fn+F9 лампочка горит что уже включен и при нажатии fn+F9 никакой реакции, можно это как то пощупать через консоль?
подскажите как через консоль это все проверить
Покажите
iwconfigну и
dmesgне помешает.
ocsana@ubuntu:~$ iwconfig
lo no wireless extensions.eth1 no wireless extensions.
ocsana@ubuntu:~$ ifconfig -a
eth1 Link encap:Ethernet HWaddr e8:11:32:d6:43:e2
inet addr:192.168.2.102 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::ea11:32ff:fed6:43e2/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:151 errors:0 dropped:0 overruns:0 frame:0
TX packets:179 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:97129 (97.1 KB) TX bytes:21539 (21.5 KB)
Interrupt:18
lo Link encap:Локальная петля (Loopback)
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:480 (480.0 B) TX bytes:480 (480.0 B)
ocsana@ubuntu:~$ [ 0.224590] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.224910] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
[ 0.225100] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
[ 0.225279] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT]
[ 0.225458] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP4._PRT]
[ 0.225641] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 0.226139] ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
[ 0.226159] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f7010e88), AE_ALREADY_EXISTS
[ 0.246469] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.246746] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 *4 5 6 7 10 11 12 14 15)
[ 0.247016] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
[ 0.247278] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.247557] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.247841] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.248152] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 *7 10 11 12 14 15)
[ 0.248432] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.248791] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.248823] vgaarb: loaded
[ 0.249149] SCSI subsystem initialized
[ 0.249412] libata version 3.00 loaded.
[ 0.249633] usbcore: registered new interface driver usbfs
[ 0.249678] usbcore: registered new interface driver hub
[ 0.249763] usbcore: registered new device driver usb
[ 0.250172] ACPI: WMI: Mapper loaded
[ 0.250179] PCI: Using ACPI for IRQ routing
[ 0.250194] pci 0000:00:1c.1: BAR 13: can't allocate resource
[ 0.250204] pci 0000:00:1c.3: BAR 13: can't allocate resource
[ 0.250634] NetLabel: Initializing
[ 0.250642] NetLabel: domain hash size = 128
[ 0.250647] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.250682] NetLabel: unlabeled traffic allowed by default
[ 0.250780] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.250794] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.250808] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.256056] Switching to clocksource tsc
[ 0.260820] AppArmor: AppArmor Filesystem Enabled
[ 0.260858] pnp: PnP ACPI init
[ 0.260895] ACPI: bus type pnp registered
[ 0.267127] pnp: PnP ACPI: found 9 devices
[ 0.267136] ACPI: ACPI bus type pnp unregistered
[ 0.267146] PnPBIOS: Disabled by ACPI PNP
[ 0.267183] system 00:01: ioport range 0x800-0x80f has been reserved
[ 0.267193] system 00:01: ioport range 0x1000-0x107f has been reserved
[ 0.267203] system 00:01: ioport range 0x1180-0x11bf has been reserved
[ 0.267213] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 0.267224] system 00:01: ioport range 0xfe00-0xfe00 has been reserved
[ 0.267233] system 00:01: ioport range 0x164e-0x174c has been reserved
[ 0.267244] system 00:01: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.267255] system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
[ 0.267265] system 00:01: iomem range 0xf8000000-0xfbffffff has been reserved
[ 0.267276] system 00:01: iomem range 0xfef00000-0xfeffffff has been reserved
[ 0.302485] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:05
[ 0.302498] pci 0000:00:1c.0: IO window: 0x3000-0x3fff
[ 0.302512] pci 0000:00:1c.0: MEM window: 0xf0100000-0xf01fffff
[ 0.302523] pci 0000:00:1c.0: PREFETCH window: 0x00000040000000-0x000000401fffff
[ 0.302538] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:07
[ 0.302547] pci 0000:00:1c.1: IO window: 0x4000-0x4fff
[ 0.302560] pci 0000:00:1c.1: MEM window: 0x40200000-0x403fffff
[ 0.302571] pci 0000:00:1c.1: PREFETCH window: 0x00000040400000-0x000000405fffff
[ 0.302587] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:09
[ 0.302595] pci 0000:00:1c.2: IO window: 0x2000-0x2fff
[ 0.302608] pci 0000:00:1c.2: MEM window: 0xf0200000-0xf02fffff
[ 0.302619] pci 0000:00:1c.2: PREFETCH window: 0x00000040600000-0x000000407fffff
[ 0.302635] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:0b
[ 0.302644] pci 0000:00:1c.3: IO window: 0x5000-0x5fff
[ 0.302656] pci 0000:00:1c.3: MEM window: 0x40800000-0x409fffff
[ 0.302667] pci 0000:00:1c.3: PREFETCH window: 0x00000040a00000-0x00000040bfffff
[ 0.302682] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:11
[ 0.302689] pci 0000:00:1e.0: IO window: disabled
[ 0.302700] pci 0000:00:1e.0: MEM window: disabled
[ 0.302709] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.302746] alloc irq_desc for 16 on node -1
[ 0.302752] alloc kstat_irqs on node -1
[ 0.302769] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.302782] pci 0000:00:1c.0: setting latency timer to 64
[ 0.302800] pci 0000:00:1c.1: enabling device (0000 -> 0003)
[ 0.302810] alloc irq_desc for 17 on node -1
[ 0.302816] alloc kstat_irqs on node -1
[ 0.302827] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.302840] pci 0000:00:1c.1: setting latency timer to 64
[ 0.302859] alloc irq_desc for 18 on node -1
[ 0.302865] alloc kstat_irqs on node -1
[ 0.302875] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.302886] pci 0000:00:1c.2: setting latency timer to 64
[ 0.302904] pci 0000:00:1c.3: enabling device (0000 -> 0003)
[ 0.302914] alloc irq_desc for 19 on node -1
[ 0.302920] alloc kstat_irqs on node -1
[ 0.302930] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.302944] pci 0000:00:1c.3: setting latency timer to 64
[ 0.302961] pci 0000:00:1e.0: setting latency timer to 64
[ 0.302972] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.302979] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.302989] pci_bus 0000:05: resource 0 io: [0x3000-0x3fff]
[ 0.302998] pci_bus 0000:05: resource 1 mem: [0xf0100000-0xf01fffff]
[ 0.303007] pci_bus 0000:05: resource 2 pref mem [0x40000000-0x401fffff]
[ 0.303017] pci_bus 0000:07: resource 0 io: [0x4000-0x4fff]
[ 0.303025] pci_bus 0000:07: resource 1 mem: [0x40200000-0x403fffff]
[ 0.303033] pci_bus 0000:07: resource 2 pref mem [0x40400000-0x405fffff]
[ 0.303071] pci_bus 0000:09: resource 0 io: [0x2000-0x2fff]
[ 0.303079] pci_bus 0000:09: resource 1 mem: [0xf0200000-0xf02fffff]
[ 0.303088] pci_bus 0000:09: resource 2 pref mem [0x40600000-0x407fffff]
[ 0.303097] pci_bus 0000:0b: resource 0 io: [0x5000-0x5fff]
[ 0.303105] pci_bus 0000:0b: resource 1 mem: [0x40800000-0x409fffff]
[ 0.303113] pci_bus 0000:0b: resource 2 pref mem [0x40a00000-0x40bfffff]
[ 0.303122] pci_bus 0000:11: resource 3 io: [0x00-0xffff]
[ 0.303130] pci_bus 0000:11: resource 4 mem: [0x000000-0xffffffff]
[ 0.303228] NET: Registered protocol family 2
[ 0.303495] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.304361] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.305485] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.306026] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.306035] TCP reno registered
[ 0.306309] NET: Registered protocol family 1
[ 0.306368] pci 0000:00:02.0: Boot video device
[ 0.306414] alloc irq_desc for 23 on node -1
[ 0.306421] alloc kstat_irqs on node -1
[ 0.306437] pci 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.306465] pci 0000:00:1d.0: PCI INT A disabled
[ 0.306483] pci 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.306509] pci 0000:00:1d.1: PCI INT B disabled
[ 0.306526] pci 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.306552] pci 0000:00:1d.2: PCI INT C disabled
[ 0.306568] pci 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 0.306593] pci 0000:00:1d.3: PCI INT D disabled
[ 0.306616] pci 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.306663] pci 0000:00:1d.7: PCI INT A disabled
[ 0.306738] Simple Boot Flag at 0x36 set to 0x1
[ 0.307233] cpufreq-nforce2: No nForce2 chipset.
[ 0.307334] Scanning for low memory corruption every 60 seconds
[ 0.307621] audit: initializing netlink socket (disabled)
[ 0.307647] type=2000 audit(1339268041.307:1): initialized
[ 0.328419] highmem bounce pool size: 64 pages
[ 0.328436] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.333609] VFS: Disk quotas dquot_6.5.2
[ 0.333802] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.335790] fuse init (API version 7.13)
[ 0.336067] msgmni has been set to 1716
[ 0.336737] alg: No test for stdrng (krng)
[ 0.336938] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.336948] io scheduler noop registered
[ 0.336954] io scheduler anticipatory registered
[ 0.336960] io scheduler deadline registered
[ 0.337096] io scheduler cfq registered (default)
[ 0.337430] alloc irq_desc for 24 on node -1
[ 0.337437] alloc kstat_irqs on node -1
[ 0.337463] pcieport 0000:00:1c.0: irq 24 for MSI/MSI-X
[ 0.337485] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.337780] alloc irq_desc for 25 on node -1
[ 0.337788] alloc kstat_irqs on node -1
[ 0.337806] pcieport 0000:00:1c.1: irq 25 for MSI/MSI-X
[ 0.337825] pcieport 0000:00:1c.1: setting latency timer to 64
[ 0.338083] alloc irq_desc for 26 on node -1
[ 0.338090] alloc kstat_irqs on node -1
[ 0.338108] pcieport 0000:00:1c.2: irq 26 for MSI/MSI-X
[ 0.338127] pcieport 0000:00:1c.2: setting latency timer to 64
[ 0.338417] alloc irq_desc for 27 on node -1
[ 0.338425] alloc kstat_irqs on node -1
[ 0.338444] pcieport 0000:00:1c.3: irq 27 for MSI/MSI-X
[ 0.338462] pcieport 0000:00:1c.3: setting latency timer to 64
[ 0.338691] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.338972] ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
[ 0.338994] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f7010e88), AE_ALREADY_EXISTS
[ 0.339387] ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
[ 0.339406] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f7010e88), AE_ALREADY_EXISTS
[ 0.339722] ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
[ 0.339743] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f7010e88), AE_ALREADY_EXISTS
[ 0.340080] ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
[ 0.340099] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f7010e88), AE_ALREADY_EXISTS
[ 0.340466] ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
[ 0.340484] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f7010e88), AE_ALREADY_EXISTS
[ 0.340813] ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
[ 0.340832] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f7010e88), AE_ALREADY_EXISTS
[ 0.341148] ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
[ 0.341167] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f7010e88), AE_ALREADY_EXISTS
[ 0.341507] ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
[ 0.341526] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f7010e88), AE_ALREADY_EXISTS
[ 0.341647] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.342175] ACPI: AC Adapter [ADP1] (off-line)
[ 0.342442] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[ 0.342545] ACPI: Lid Switch [LID0]
[ 0.342676] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 0.342691] ACPI: Power Button [PWRB]
[ 0.342827] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[ 0.342837] ACPI: Sleep Button [SLPB]
[ 0.342978] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 0.342987] ACPI: Power Button [PWRF]
[ 0.344715] ACPI: SSDT 3f5b9a1f 00203 (v02 PmRef Cpu0Ist 00003000 INTL 20050624)
[ 0.346030] ACPI: SSDT 3f5b9188 00708 (v02 PmRef Cpu0Cst 00003001 INTL 20050624)
[ 0.352443] Monitor-Mwait will be used to enter C-1 state
[ 0.352552] processor LNXCPU:00: registered as cooling_device0
[ 0.353666] ACPI: SSDT 3f5b9c22 000D4 (v02 PmRef Cpu1Ist 00003000 INTL 20050624)
[ 0.354586] ACPI: SSDT 3f5b9890 00085 (v02 PmRef Cpu1Cst 00003000 INTL 20050624)
[ 0.359908] processor LNXCPU:01: registered as cooling_device1
[ 0.367622] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.367647] ACPI: Thermal Zone [TZ00] (56 C)
[ 0.372573] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.376439] brd: module loaded
[ 0.377977] loop: module loaded
[ 0.378260] input: Macintosh mouse button emulation as /devices/virtual/input/input4
[ 0.379311] isapnp: Scanning for PnP cards...
[ 0.380100] Fixed MDIO Bus: probed
[ 0.380210] PPP generic driver version 2.4.2
[ 0.380390] tun: Universal TUN/TAP device driver, 1.6
[ 0.380418] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.380910] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.380956] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.380993] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.381001] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.381107] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 0.381155] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[ 0.381175] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.385084] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 0.385141] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf0604000
[ 0.399854] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.400133] usb usb1: configuration #1 chosen from 1 choice
[ 0.400215] hub 1-0:1.0: USB hub found
[ 0.400236] hub 1-0:1.0: 8 ports detected
[ 0.400396] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.400440] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.400516] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.400535] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.400543] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.400639] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 0.400684] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001820
[ 0.400923] usb usb2: configuration #1 chosen from 1 choice
[ 0.401004] hub 2-0:1.0: USB hub found
[ 0.401025] hub 2-0:1.0: 2 ports detected
[ 0.401133] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.401149] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.401157] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.401247] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 0.401304] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001840
[ 0.401530] usb usb3: configuration #1 chosen from 1 choice
[ 0.401610] hub 3-0:1.0: USB hub found
[ 0.401627] hub 3-0:1.0: 2 ports detected
[ 0.401730] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.401747] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.401755] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.401851] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 0.401904] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860
[ 0.402135] usb usb4: configuration #1 chosen from 1 choice
[ 0.402209] hub 4-0:1.0: USB hub found
[ 0.402226] hub 4-0:1.0: 2 ports detected
[ 0.402335] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 0.402350] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 0.402359] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 0.402447] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 0.402499] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001880
[ 0.402730] usb usb5: configuration #1 chosen from 1 choice
[ 0.402805] hub 5-0:1.0: USB hub found
[ 0.402822] hub 5-0:1.0: 2 ports detected
[ 0.403043] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE1] at 0x60,0x64 irq 1,12
[ 0.405545] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.405567] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.405782] mice: PS/2 mouse device common for all mice
[ 0.406256] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 0.406303] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 0.406604] device-mapper: uevent: version 1.0.3
[ 0.411685] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 0.439321] device-mapper: multipath: version 1.1.0 loaded
[ 0.439331] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.439740] EISA: Probing bus 0 at eisa.0
[ 0.439752] Cannot allocate resource for EISA slot 1
[ 0.439759] Cannot allocate resource for EISA slot 2
[ 0.439766] Cannot allocate resource for EISA slot 3
[ 0.439772] Cannot allocate resource for EISA slot 4
[ 0.439778] Cannot allocate resource for EISA slot 5
[ 0.439798] EISA: Detected 0 cards.
[ 0.451852] cpuidle: using governor ladder
[ 0.451860] cpuidle: using governor menu
[ 0.453023] TCP cubic registered
[ 0.453520] NET: Registered protocol family 10
[ 0.455667] NET: Registered protocol family 17
[ 0.456849] Using IPI No-Shortcut mode
[ 0.457072] PM: Resume from disk failed.
[ 0.457099] registered taskstats version 1
[ 0.457950] Magic number: 0:476:948
[ 0.457993] tty tty5: hash matches
[ 0.458089] rtc_cmos 00:04: setting system clock to 2012-06-09 18:54:01 UTC (1339268041)
[ 0.458097] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.458103] EDD information not available.
[ 0.464018] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[ 0.503234] ACPI: Battery Slot [BAT1] (battery present)
[ 0.669566] Freeing initrd memory: 7818k freed
[ 0.734026] isapnp: No Plug & Play device found
[ 0.734068] Freeing unused kernel memory: 664k freed
[ 0.734714] Write protecting the kernel text: 4700k
[ 0.734787] Write protecting the kernel read-only data: 1848k
[ 0.769873] udev: starting version 151
[ 0.854239] usb 1-8: new high speed USB device using ehci_hcd and address 3
[ 1.010616] usb 1-8: configuration #1 chosen from 1 choice
[ 1.045581] sky2 driver version 1.25
[ 1.045729] sky2 0000:09:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.045791] sky2 0000:09:00.0: setting latency timer to 64
[ 1.045921] sky2 0000:09:00.0: Yukon-2 FE+ chip revision 0
[ 1.046489] alloc irq_desc for 28 on node -1
[ 1.046495] alloc kstat_irqs on node -1
[ 1.046583] sky2 0000:09:00.0: irq 28 for MSI/MSI-X
[ 1.048724] sky2 eth0: addr e8:11:32:d6:43:e2
[ 1.069259] ahci 0000:00:1f.2: version 3.0
[ 1.069296] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.069376] alloc irq_desc for 29 on node -1
[ 1.069383] alloc kstat_irqs on node -1
[ 1.069407] ahci 0000:00:1f.2: irq 29 for MSI/MSI-X
[ 1.069549] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[ 1.069561] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
[ 1.069574] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.070145] scsi0 : ahci
[ 1.070508] scsi1 : ahci
[ 1.070730] scsi2 : ahci
[ 1.070939] scsi3 : ahci
[ 1.071370] ata1: SATA max UDMA/133 abar m1024@0xf0604400 port 0xf0604500 irq 29
[ 1.071382] ata2: SATA max UDMA/133 abar m1024@0xf0604400 port 0xf0604580 irq 29
[ 1.071392] ata3: SATA max UDMA/133 abar m1024@0xf0604400 port 0xf0604600 irq 29
[ 1.071402] ata4: SATA max UDMA/133 abar m1024@0xf0604400 port 0xf0604680 irq 29
[ 1.252043] usb 3-1: new full speed USB device using uhci_hcd and address 2
[ 1.388075] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.388112] ata3: SATA link down (SStatus 0 SControl 300)
[ 1.388143] ata4: SATA link down (SStatus 0 SControl 300)
[ 1.388179] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.394139] ata1.00: ATA-8: SAMSUNG HM321HI, 2AJ10002, max UDMA/133
[ 1.394147] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.400235] ata1.00: configured for UDMA/133
[ 1.416311] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HM321HI 2AJ1 PQ: 0 ANSI: 5
[ 1.416792] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.417112] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 1.417245] sd 0:0:0:0: [sda] Write Protect is off
[ 1.417252] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.417319] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.417664] sda:
[ 1.433597] usb 3-1: configuration #1 chosen from 1 choice
[ 1.442502] sda1 sda2 < sda5
[ 1.469716] usbcore: registered new interface driver hiddev
[ 1.470675] sda6 >
[ 1.471648] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.474905] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input6
[ 1.475205] generic-usb 0003:046D:C52F.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.1-1/input0
[ 1.480673] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.1/input/input7
[ 1.481096] generic-usb 0003:046D:C52F.0002: input,hiddev96,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.1-1/input1
[ 1.481179] usbcore: registered new interface driver usbhid
[ 1.481190] usbhid: v2.6:USB HID core driver
[ 1.761528] EXT4-fs (sda1): mounted filesystem with ordered data mode
[ 8.314164] Adding 1951736k swap on /dev/sda5. Priority:-1 extents:1 across:1951736k
[ 8.367176] udev: starting version 151
[ 8.546828] lp: driver loaded but no devices found
[ 8.607634] udev: renamed network interface eth0 to eth1
[ 8.825597] Linux agpgart interface v0.103
[ 8.983968] Linux video capture interface: v2.00
[ 9.011683] agpgart-intel 0000:00:00.0: Intel IGD Chipset
[ 9.011982] agpgart-intel 0000:00:00.0: detected 8188K stolen memory
[ 9.097547] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[ 9.167213] psmouse serio1: ID: 10 00 64
[ 9.184923] type=1505 audit(1339257250.222:2): operation="profile_load" pid=547 name="/sbin/dhclient3"
[ 9.216715] type=1505 audit(1339257250.254:3): operation="profile_load" pid=547 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 9.217179] type=1505 audit(1339257250.258:4): operation="profile_load" pid=547 name="/usr/lib/connman/scripts/dhclient-script"
[ 9.219588] [drm] Initialized drm 1.1.0 20060810
[ 9.251085] uvcvideo: Found UVC 1.00 device USB 2.0 PC Camera (1210:25f4)
[ 9.254770] input: USB 2.0 PC Camera as /devices/pci0000:00/0000:00:1d.7/usb1/1-8/1-8:1.0/input/input8
[ 9.254955] usbcore: registered new interface driver uvcvideo
[ 9.254967] USB Video Class driver (v0.1.0)
[ 9.268208] elantech.c: assuming hardware version 2, firmware version 4.2.22
[ 9.304094] elantech.c: Synaptics capabilities query result 0x09, 0x14, 0x0b.
[ 9.441999] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 9.442013] i915 0000:00:02.0: setting latency timer to 64
[ 9.443546] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input9
[ 9.496109] alloc irq_desc for 30 on node -1
[ 9.496118] alloc kstat_irqs on node -1
[ 9.496138] i915 0000:00:02.0: irq 30 for MSI/MSI-X
[ 9.496154] [drm] set up 7M of stolen space
[ 9.641820] [drm] initialized overlay support
[ 10.096601] fb0: inteldrmfb frame buffer device
[ 10.096609] registered panic notifier
[ 10.096657] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 10.096748] alloc irq_desc for 22 on node -1
[ 10.096755] alloc kstat_irqs on node -1
[ 10.096770] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 10.096827] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 10.103905] vga16fb: initializing
[ 10.103917] vga16fb: mapped to 0xc00a0000
[ 10.103927] vga16fb: not registering due to another framebuffer present
[ 10.201088] [drm] Big FIFO is enabled
[ 10.201107] [drm] Big FIFO is enabled
[ 10.218957] EXT4-fs (sda6): mounted filesystem with ordered data mode
[ 10.248836] hda_codec: ALC269: BIOS auto-probing.
[ 10.249417] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input10
[ 10.427593] Console: switching to colour frame buffer device 128x37
[ 10.621749] type=1505 audit(1339257251.662:5): operation="profile_load" pid=740 name="/usr/share/gdm/guest-session/Xsession"
[ 10.671035] type=1505 audit(1339257251.710:6): operation="profile_load" pid=748 name="/usr/bin/evince"
[ 10.681830] type=1505 audit(1339257251.722:7): operation="profile_load" pid=748 name="/usr/bin/evince-previewer"
[ 10.693073] type=1505 audit(1339257251.734:8): operation="profile_load" pid=748 name="/usr/bin/evince-thumbnailer"
[ 10.726451] type=1505 audit(1339257251.766:9): operation="profile_load" pid=758 name="/usr/lib/cups/backend/cups-pdf"
[ 10.727482] type=1505 audit(1339257251.766:10): operation="profile_load" pid=758 name="/usr/sbin/cupsd"
[ 10.743100] type=1505 audit(1339257251.782:11): operation="profile_load" pid=761 name="/usr/sbin/tcpdump"
[ 10.942185] sky2 eth1: enabling interface
[ 10.951582] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 11.335178] ppdev: user-space parallel port driver
[ 11.916848] CPU0 attaching NULL sched-domain.
[ 11.916863] CPU1 attaching NULL sched-domain.
[ 11.945244] CPU0 attaching sched-domain:
[ 11.945252] domain 0: span 0-1 level SIBLING
[ 11.945259] groups: 0 (cpu_power = 589) 1 (cpu_power = 589)
[ 11.945294] domain 1: span 0-1 level MC
[ 11.945299] groups: 0-1 (cpu_power = 1178)
[ 11.945310] CPU1 attaching sched-domain:
[ 11.945315] domain 0: span 0-1 level SIBLING
[ 11.945320] groups: 1 (cpu_power = 589) 0 (cpu_power = 589)
[ 11.945334] domain 1: span 0-1 level MC
[ 11.945340] groups: 0-1 (cpu_power = 1178)
[ 13.786668] sky2 eth1: Link is up at 100 Mbps, full duplex, flow control both
[ 13.787545] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 15.454073] CPU0 attaching NULL sched-domain.
[ 15.454088] CPU1 attaching NULL sched-domain.
[ 15.484202] CPU0 attaching sched-domain:
[ 15.484213] domain 0: span 0-1 level SIBLING
[ 15.484223] groups: 0 (cpu_power = 589) 1 (cpu_power = 589)
[ 15.484241] domain 1: span 0-1 level MC
[ 15.484249] groups: 0-1 (cpu_power = 1178)
[ 15.484266] CPU1 attaching sched-domain:
[ 15.484274] domain 0: span 0-1 level SIBLING
[ 15.484282] groups: 1 (cpu_power = 589) 0 (cpu_power = 589)
[ 15.484300] domain 1: span 0-1 level MC
[ 15.484308] groups: 0-1 (cpu_power = 1178)
[ 23.880028] eth1: no IPv6 routers present
[ 54.767283] CPU0 attaching NULL sched-domain.
[ 54.767294] CPU1 attaching NULL sched-domain.
[ 54.792919] CPU0 attaching sched-domain:
[ 54.792930] domain 0: span 0-1 level SIBLING
[ 54.792939] groups: 0 (cpu_power = 589) 1 (cpu_power = 589)
[ 54.792955] domain 1: span 0-1 level MC
[ 54.792962] groups: 0-1 (cpu_power = 1178)
[ 54.792977] CPU1 attaching sched-domain:
[ 54.792984] domain 0: span 0-1 level SIBLING
[ 54.792992] groups: 1 (cpu_power = 589) 0 (cpu_power = 589)
[ 54.793007] domain 1: span 0-1 level MC
[ 54.793014] groups: 0-1 (cpu_power = 1178)
[ 54.812342] ACPI Error (psargs-0359): [\_SB_.VDRV] Namespace lookup failure, AE_NOT_FOUND
[ 54.812364] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.LPC0.H_EC._Q51] (Node f7014570), AE_NOT_FOUND
ocsana@ubuntu:~$ не.
для начала
lspci -knn | grep "Eth\|Net" -A2
?
lspci -kпоставил 12.04 вроде заработал вайфай, а проблема была в том что стандартные команды с fn не работали и я не мог включить вафлю которая горела что работает
))
для этого переставлять осю было не обязательно.
ну и аминь.
))
для этого переставлять осю было не обязательно.
ну и аминь.
просто проблему нужно было быстро решить пока я там. А 12.04 чудесно встало да и для нет бука по приятнее будет.
Лови, почти универсальный способ Настройка WiFi в ArchLinux
У меня тоже такая проблема была, вот и решил статейку написать
Мне тоже не получалось завести свою вафлю на версиях нижу 12.04
Лови, почти универсальный способ Настройка WiFi в ArchLinux
У меня тоже такая проблема была, вот и решил статейку написать
+1
а тем ку то я в закладочки кинул, мало ли кому еше придется поднимать.
А поставил я Ubuntu маме моего друга, она сидит чисто в одноклассниках. У неё стояла "замечу off" Виндоус 7
аппарат тощий и винда малость лагала. Ну я хотел поставить то что у меня и в что я уверен на 100% ubuntu 10.04 но так вышло, и теперь там 12.04 красиво и работает.
Аппарат работает шустрее винды но все же похуже 10.04
PS. я конечно обалдел когда друг позвонил с такой просьбой. Хотя он не сильно сторонник линукса.
Теперь он прикалывается через PuTTY
что то вроде
"мама хочу есть!!! сынок я в однокласниках."
и тут решает PuTTY sudo shutdown -P +5
" Ну ладно мам через 5 минут нетбук выключится как рас покушать даш"
Думаю он заинтересовался возможностями Ubuntu ))))
Теперь найти бы как подключится мне туда, в обход роутера. было бы вообще шикарно )
Теперь найти бы как подключится мне туда, в обход роутера. было бы вообще шикарно )
На роутере пробросить порт.
Если внешний адрес динамический, использовать что-то вроде DynDNS или no-ip. Ну и роутер должен эту «фишку» поддерживать.
вот у меня у самого есть роутер, комп есть и ноут. Я знаю локальные адреса могу с одного рулить вторым, но и в кошмаре незнаю как это сделать через внешний ип.
зависит от прошивы роутера. У каждого изготовителя проброс находится чертиде и называется чертикак... Но общий смысл - должна быть таблица соответствия порт - адрес. Иногда бывает порт - диапазон адресов или порт - адрес получателя+порт получателя.
Ну а дальше все просто: узнаешь айпи, и тупа лезешь туда по этому адресу и порту.
ПС: В подавляющем большинстве роутеры стоят от убогенького дырлинька. Можно попробовать поствить прошиву от dd-wrt или одну из open-wrt. Список поддерживаемых устройств тут
ПС: В подавляющем большинстве роутеры стоят от убогенького дырлинька. Можно попробовать поствить прошиву от dd-wrt или одну из open-wrt. Список поддерживаемых устройств тут
ну в таком случаи затраченное время и полученное удовольствие разные, и затраты будут большие.
Rassol2, модель роутера назовите — так будет проще что-то конкретное посоветовать.
edimax br-6228ns
Конкретно для вашей модели не нашёл, но есть аналогичные.
Edimax BR-6214K
Edimax BR-6216Mg
Думаю, будет очень похоже.
В качестве совета: поменяйте номер порта на внешнем интерфейсе на что-нибудь менее примечательное, чем 22, особенно, если аутентификация производится не по ключам, а по паролю. Да, и на всякий случай — использовать учётную запись root для удалённого входа — моветон 
Страницы 1
Чтобы отправить ответ, вы должны войти или зарегистрироваться
Linux Forum → Ubuntu, Linux Mint → samsung NP-N145 соединение по вайфай
Форум работает на PunBB, при поддержке Informer Technologies, Inc
