1 (18.06.2012 15:41:02 отредактировано IgorF)

Уважаемые форумчане, помогите решить следующую проблему:
Есть однопалатный компьютер и надо на нем заставить работать видео проигрыватель.
Вот исходные данные:
CPU: Intel® Atom™ Processor N450/D510
VGA/LVDS: Embedded Gen3.5+ GFX Core

Беда в том что для корректной работы проигрывателя нужно чтоб в системе была настроена X-Video extension, а для него нужно поставить драйвера для видео карты, причем не vesa.

Краткая история что я пробивал:
1. Проверил стандартные драйвера - не подходят
2. Обновил систему и поставил intellinuxgraphics.org/2011Q4.html (без ядра), но драйвер не грузиться, что то не видит

Если у кого есть какие соображения прошу сообщить.

2

что в качестве базового дистрибутива используешь?
стандартные утилитки на борту есть? или возможность их поставить/собрать? lspci -k | grep -i vga -A4в студию.
xorg.conf есть? в студию. если там про везу - снести.
модуль i915 загружен? есть? грузится? если есть, но не грузится dmesg в студию.
ну и логи иксов для подтверждения, что грузится именно vesa...

95% процентов проблем находятся между клавиатурой и стулом.

3

Это для intel_drv.so
dmesg

+ открыть спойлер

Linux version 2.6.18-238.19.1.el5 (root@build.vniins) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-50)) #0 SMP Thu Aug 26 00:00:00 MSD 2010
Command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
BIOS-provided physical RAM map:
BIOS-e820: 0000000000010000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003f6a0000 (usable)
BIOS-e820: 000000003f6a0000 - 000000003f6ae000 (ACPI data)
BIOS-e820: 000000003f6ae000 - 000000003f6e0000 (ACPI NVS)
BIOS-e820: 000000003f6e0000 - 000000003f700000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
DMI present.
ACPI: RSDP (v002 ACPIAM                                ) @ 0x00000000000f9dc0
ACPI: XSDT (v001 032410 XSDT1112 0x20100324 MSFT 0x00000097) @ 0x000000003f6a0100
ACPI: FADT (v004 032410 FACP1112 0x20100324 MSFT 0x00000097) @ 0x000000003f6a0290
ACPI: MADT (v002 032410 APIC1112 0x20100324 MSFT 0x00000097) @ 0x000000003f6a0390
ACPI: MCFG (v001 032410 OEMMCFG  0x20100324 MSFT 0x00000097) @ 0x000000003f6a0400
ACPI: OEMB (v001 032410 OEMB1112 0x20100324 MSFT 0x00000097) @ 0x000000003f6ae040
ACPI: GSCI (v001 032410 GMCHSCI  0x20100324 MSFT 0x00000097) @ 0x000000003f6ae0c0
ACPI: SSDT (v001  PmRef    CpuPm 0x00003000 INTL 0x20051117) @ 0x000000003f6b09f0
ACPI: DSDT (v002  362Nx 362Nx021 0x00000021 INTL 0x20051117) @ 0x0000000000000000
No NUMA configuration found
Faking a node at 0000000000000000-000000003f6a0000
Bootmem setup node 0 0000000000000000-000000003f6a0000
bootmap start 19000 pages 8
Memory for crash kernel (0x0 to 0x0) notwithin permissible range
disabling kdump
Setting up node 0 0-3f6a0
On node 0 totalpages: 254684
  DMA zone: 2531 pages, LIFO batch:0
  DMA32 zone: 252153 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 7:12 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 7:12 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to physical flat
Using ACPI (MADT) for SMP configuration information
Nosave address range: 000000000009f000 - 00000000000a0000
Nosave address range: 00000000000a0000 - 00000000000e0000
Nosave address range: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at 40000000 (gap: 3f700000:bf700000)
SMP: Allowing 4 CPUs, 2 hotplug CPUs
Built 1 zonelists.  Total pages: 254684
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Checking aperture...
ACPI: DMAR not present
Memory: 1013528k/1038976k available (2554k kernel code, 24996k reserved, 1633k data, 224k init)
Calibrating delay loop (skipped), value calculated using timer frequency.. 3324.69 BogoMIPS (lpj=1662349)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 24K
CPU: L2 cache: 512K
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
Using local APIC timer interrupts.
Detected 10.389 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3324.11 BogoMIPS (lpj=1662055)
CPU: L1 I cache: 32K, L1 D cache: 24K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU1: Thermal monitoring enabled (TM2)
         Intel(R) Atom(TM) CPU N450   @ 1.66GHz stepping 0a
Brought up 2 CPUs
CPU#0: NMI watchdog performance counter calibration - 143->163
CPU#1: NMI watchdog performance counter calibration - 60->81
NMI watchdog testing PASSED.
time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer.
time.c: Detected 1662.349 MHz processor.
sizeof(vma)=176 bytes
sizeof(page)=56 bytes
sizeof(inode)=560 bytes
sizeof(dentry)=216 bytes
sizeof(ext3inode)=760 bytes
sizeof(buffer_head)=96 bytes
sizeof(skbuff)=248 bytes
migration_cost=13
checking if image is initramfs... it is
Freeing initrd memory: 3077k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 *6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: IRQ 4 override to edge, high
pnp: IRQ 3 override to edge, high
pnp: IRQ 11 override to edge, high
pnp: IRQ 10 override to edge, high
pnp: PnP ACPI: found 20 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
ACPI: DMAR not present
PCI-GART: No AMD northbridge found.
pnp: 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
pnp: 00:01: iomem range 0xfed90000-0xfed93fff has been reserved
pnp: 00:09: ioport range 0xa00-0xa7f has been reserved
pnp: 00:0a: iomem range 0xfed1c000-0xfed1ffff has been reserved
pnp: 00:0a: iomem range 0xfed20000-0xfed3ffff has been reserved
pnp: 00:0a: iomem range 0xfed40000-0xfed8ffff has been reserved
pnp: 00:0c: iomem range 0xffc00000-0xffefffff could not be reserved
pnp: 00:0d: iomem range 0xfec00000-0xfec00fff has been reserved
pnp: 00:0d: iomem range 0xfee00000-0xfee00fff could not be reserved
pnp: 00:12: iomem range 0xe0000000-0xefffffff has been reserved
pnp: 00:13: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:13: iomem range 0xc0000-0xcffff could not be reserved
pnp: 00:13: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:13: iomem range 0x100000-0x3f6fffff could not be reserved
PCI: Bridge: 0000:00:1c.0
  IO window: e000-efff
  MEM window: feb00000-febfffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 22 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
type=2000 audit(1340050558.805:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
alg: No test for crc32c (crc32c-generic)
ksign: Installing public key data
Loading keyring
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:00:02.0
PCI: Setting latency timer of device 0000:00:1c.0 to 64
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI (exconfig-0456): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu0Ist] [20060707]
ACPI (exconfig-0456): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu0Cst] [20060707]
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI (exconfig-0456): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu1Ist] [20060707]
ACPI (exconfig-0456): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu1Cst] [20060707]
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
serial8250: ttyS2 at I/O 0x3e8 (irq = 11) is a 16550A
serial8250: ttyS3 at I/O 0x2e8 (irq = 10) is a 16550A
00:0e: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0f: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:10: ttyS2 at I/O 0x3e8 (irq = 11) is a 16550A
00:11: ttyS3 at I/O 0x2e8 (irq = 10) is a 16550A
brd: module loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH8M: IDE controller at PCI slot 0000:00:1f.1
GSI 17 sharing vector 0xC1 and IRQ 17
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 19 (level, low) -> IRQ 193
ICH8M: chipset revision 4
ICH8M: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
hda: TS16GCF600, CFA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 512KiB
hda: 31293360 sectors (16022 MB) w/1KiB Cache, CHS=31045/255/63, UDMA(100)
hda: hda1 hda2
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S1 S3 S4 S5)
Initalizing network drop monitor service
Freeing unused kernel memory: 224k freed
Write protecting the kernel read-only data: 500k
input: AT Translated Set 2 keyboard as /class/input/input0
GSI 18 sharing vector 0xC9 and IRQ 18
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 201, io mem 0xfeaff800
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 201, io base 0x0000cc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1 -> GSI 19 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 193, io base 0x0000c880
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-5: new high speed USB device using ehci_hcd and address 2
GSI 19 sharing vector 0xD1 and IRQ 19
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 209, io base 0x0000c800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
GSI 20 sharing vector 0xD9 and IRQ 20
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 217, io base 0x0000c480
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
SCSI subsystem initialized
libata version 3.00 loaded.
ata_piix 0000:00:1f.2: version 2.12
ACPI: PCI Interrupt 0000:00:1f.2 -> GSI 18 (level, low) -> IRQ 209
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
usb 1-5: configuration #1 chosen from 1 choice
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0xdc00 ctl 0xd880 bmdma 0xd400 irq 209
ata2: SATA max UDMA/133 cmd 0xd800 ctl 0xd480 bmdma 0xd408 irq 209
ata1: SATA link down (SStatus 0 SControl 310)
ata2: SATA link down (SStatus 0 SControl 0)
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.11.5-ioctl (2007-12-12) initialised: dm-devel@redhat.com
device-mapper: dm-raid45: initialized v0.2594l
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
GSI 21 sharing vector 0xE1 and IRQ 21
ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 17 (level, low) -> IRQ 225
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
input: PC Speaker as /class/input/input2
GSI 22 sharing vector 0xE9 and IRQ 22
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hda_codec: ALC888: BIOS auto-probing.
input: HDA Digital PCBeep as /class/input/input3
e1000e: Intel(R) PRO/1000 Network Driver - 1.2.10-NAPI
e1000e: Copyright(c) 1999 - 2010 Intel Corporation.
ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 23 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:19.0 to 64
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
pci0000:00: eth0: (PCI Express:2.5GB/s:Width x1) 00:0b:ab:3a:6e:ac
pci0000:00: eth0: Intel(R) PRO/1000 Network Connection
pci0000:00: eth0: MAC: 7, PHY: 8, PBA No: ffffff-0ff
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:02:00.0 to 64
e1000e 0000:02:00.0: Disabling ASPM L0s
pcieport-driver 0000:00:1c.0: eth1: (PCI Express:2.5GB/s:Width x1) 00:0b:ab:3a:6e:ad
pcieport-driver 0000:00:1c.0: eth1: Intel(R) PRO/1000 Network Connection
pcieport-driver 0000:00:1c.0: eth1: MAC: 5, PHY: 8, PBA No: ffffff-0ff
Linux video capture interface: v2.00
usbcore: registered new driver snd-usb-audio
uvcvideo: Found UVC 1.00 device <unnamed> (046d:0825)
input: UVC Camera (046d:0825) as /class/input/input4
usbcore: registered new driver uvcvideo
USB Video Class driver (v0.1.0)
ksm loaded
floppy0: no floppy controllers found
work still pending
lp0: using parport0 (interrupt-driven).
lp0: console ready
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Mapper loaded
dell-wmi: No known WMI GUID found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.6 loaded
loop: loaded (max 8 devices)
EXT3 FS on dm-0, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2064376k swap on /dev/mapper/VolGroup00-LogVol01.  Priority:-1 extents:1 across:2064376k
IA-32 Microcode Update Driver: v1.14a <tigran@veritas.com>
Loading iSCSI transport class v2.0-871.
cxgb3i: tag itt 0x1fff, 13 bits, age 0xf, 4 bits.
iscsi: registered transport (cxgb3i)
IPv6: Loaded, but administratively disabled, reboot required to enable
Broadcom NetXtreme II CNIC Driver cnic v2.1.2 (May 26, 2010)
Broadcom NetXtreme II iSCSI Driver bnx2i v2.1.3 (Aug 10, 2010)
iscsi: registered transport (bnx2i)
iscsi: registered transport (tcp)
iscsi: registered transport (iser)
iscsi: registered transport (be2iscsi)
Bridge firewalling registered
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (4058 buckets, 32464 max) - 304 bytes per conntrack
hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hda: drive_cmd: error=0x04 { DriveStatusError }
ide: failed opcode was: 0xa1
usb 1-6: new high speed USB device using ehci_hcd and address 3
usb 1-6: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
  Vendor: JetFlash  Model: Transcend 4GB     Rev: 8.07
  Type:   Direct-Access                      ANSI SCSI revision: 02
SCSI device sda: 7843840 512-byte hdwr sectors (4016 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 7843840 512-byte hdwr sectors (4016 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda: sda1
sd 2:0:0:0: Attached scsi removable disk sda
usb-storage: device scan complete
sd 2:0:0:0: Attached scsi generic sg0 type 0
[drm] Initialized drm 1.0.1 20051102

lspci : -k не поддерживается

+ открыть спойлер

00:02.0 VGA compatible controller: Intel Corporation N10 Family Integrated Graphics Controller (prog-if 00 [VGA controller])
    Subsystem: Intel Corporation N10 Family Integrated Graphics Controller
    Flags: bus master, fast devsel, latency 0, IRQ 15
    Memory at fea00000 (32-bit, non-prefetchable) [size=512K]
    I/O ports at c080 [size=8]
    Memory at d0000000 (32-bit, prefetchable) [size=256M]
    Memory at fe900000 (32-bit, non-prefetchable) [size=1M]
    Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
    Capabilities: [d0] Power Management version 2

00:02.1 Display controller: Intel Corporation N10 Family Integrated Graphics Controller
    Subsystem: Intel Corporation Unknown device a011
    Flags: bus master, fast devsel, latency 0
    Memory at fe880000 (32-bit, non-prefetchable) [size=512K]
    Capabilities: [d0] Power Management version 2

xorg.conf

+ открыть спойлер

# /.../
# SaX generated X11 config file
# Created on: 2012-05-25T17:48:03+0400.
#
# Version: 8.1
# Contact: Marcus Schaefer <sax@suse.de>, 2005
#
# Automatically generated by [ISaX] (8.1)
# PLEASE DO NOT EDIT THIS FILE!
#

Section "Files"
  FontPath     "/usr/lib64/X11/fonts/misc:unscaled"
  FontPath     "/usr/lib64/X11/fonts/local"
  FontPath     "/usr/lib64/X11/fonts/75dpi:unscaled"
  FontPath     "/usr/lib64/X11/fonts/100dpi:unscaled"
  FontPath     "/usr/lib64/X11/fonts/Type1"
  FontPath     "/usr/lib64/X11/fonts/URW"
  FontPath     "/usr/lib64/X11/fonts/Speedo"
  FontPath     "/usr/lib64/X11/fonts/PEX"
  FontPath     "/usr/lib64/X11/fonts/cyrillic"
  FontPath     "/usr/lib64/X11/fonts/latin2/misc:unscaled"
  FontPath     "/usr/lib64/X11/fonts/latin2/75dpi:unscaled"
  FontPath     "/usr/lib64/X11/fonts/latin2/100dpi:unscaled"
  FontPath     "/usr/lib64/X11/fonts/latin2/Type1"
  FontPath     "/usr/lib64/X11/fonts/latin7/75dpi:unscaled"
  FontPath     "/usr/lib64/X11/fonts/baekmuk:unscaled"
  FontPath     "/usr/lib64/X11/fonts/japanese:unscaled"
  FontPath     "/usr/lib64/X11/fonts/kwintv"
  FontPath     "/usr/lib64/X11/fonts/truetype"
  FontPath     "/usr/lib64/X11/fonts/uni:unscaled"
  FontPath     "/usr/lib64/X11/fonts/CID"
  FontPath     "/usr/lib64/X11/fonts/ucs/misc:unscaled"
  FontPath     "/usr/lib64/X11/fonts/ucs/75dpi:unscaled"
  FontPath     "/usr/lib64/X11/fonts/ucs/100dpi:unscaled"
  FontPath     "/usr/lib64/X11/fonts/hellas/misc:unscaled"
  FontPath     "/usr/lib64/X11/fonts/hellas/75dpi:unscaled"
  FontPath     "/usr/lib64/X11/fonts/hellas/100dpi:unscaled"
  FontPath     "/usr/lib64/X11/fonts/hellas/Type1"
  FontPath     "/usr/lib64/X11/fonts/misc/sgi:unscaled"
  FontPath     "/usr/lib64/X11/fonts/xtest"
  FontPath     "/opt/kde3/share/fonts"
EndSection

Section "ServerFlags"
  Option       "AllowMouseOpenFail" "on"
  Option       "ZapWarning" "on"
EndSection

Section "Module"
  Load         "dri2"
  Load         "dbe"
  Load         "glx"
  Load         "extmod"
  Load         "dri"
EndSection

Section "InputDevice"
  Driver       "kbd"
  Identifier   "Keyboard[0]"
  Option       "Protocol" "Standard"
  Option       "XkbLayout" "us"
  Option       "XkbModel" "pc104"
  Option       "XkbOptions" "grp:ctrl_shift_toggle"
  Option       "XkbRules" "xorg"
EndSection


Section "InputDevice"
  Driver       "mouse"
  Identifier   "Mouse[1]"
  Option       "Buttons" "4"
  Option       "Device" "/dev/input/mouse0"
  Option       "InvX" "on"
  Option       "InvY" "on"
  Option       "Name" "eGalax USB TouchController"
  Option       "Protocol" "ExplorerPS/2"
  Option       "Rotate" "cw"
  Option       "Vendor" "Sysp"
  Option       "ZAxisMapping" "4 5"
EndSection


Section "Monitor"
  DisplaySize  376 301
  HorizSync    30-81
  Identifier   "Monitor[0]"
  ModelName    "SAMSUNG SMB1940"
  Option       "DPMS"
  Option       "PreferredMode" "1280x1024"
  VendorName   "SAM"
  VertRefresh  43-75
  UseModes     "Modes[0]"
EndSection


Section "Modes"
  Identifier   "Modes[0]"
  Modeline     "1280x1024" 108 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync
EndSection


Section "Screen"
  DefaultDepth 24
  SubSection "Display"
    Depth      15
    Modes      "1280x1024"
  EndSubSection
  SubSection "Display"
    Depth      16
    Modes      "1280x1024"
  EndSubSection
  SubSection "Display"
    Depth      24
    Modes      "1280x1024"
  EndSubSection
  SubSection "Display"
    Depth      8
    Modes      "1280x1024"
  EndSubSection
  Device       "Device[0]"
  Identifier   "Screen[0]"
  Monitor      "Monitor[0]"
EndSection


Section "Device"
  BoardName    "Vesa-BIOS Graphics"
  Driver       "intel"
  Identifier   "Device[0]"
  Option       "DefaultRefresh"
  Option       "ShadowFB"
  Option       "ModeSetClearScreen"
  Screen       0
  VendorName   "VESA"
EndSection



Section "ServerLayout"
        #InputDevice "EETI" "SendCoreEvents"
  Identifier   "Layout[all]"
  InputDevice  "Keyboard[0]" "CoreKeyboard"
  InputDevice  "Mouse[1]" "CorePointer"
  Option       "Clone" "off"
  Option       "Xinerama" "off"
  Screen       "Screen[0]"
EndSection


Section "DRI"
    Group      "video"
    Mode       0660
EndSection

Section "Extensions"
EndSection

startx

+ открыть спойлер

xauth:  creating new authority file /root/.serverauth.4464

_XSERVTransSocketOpenCOTSServer: Unable to open socket for inet6
_XSERVTransOpen: transport open failed for inet6/localhost.localdomain:0
_XSERVTransMakeAllCOTSServerListeners: failed to open listener for inet6

This is a pre-release version of the X server from The X.Org Foundation.
It is not supported in any way.
Bugs may be filed in the bugzilla at
Select the "xorg" product for bugs you find in this release.
Before reporting bugs in pre-release versions please check the
latest version in the X.Org Foundation git repository.


X.Org X Server 1.6.99.903 (1.7.0 RC 3)
Release Date: 2009-9-28
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.18-238.19.1.el5 x86_64
Current Operating System: Linux localhost.localdomain 2.6.18-238.19.1.el5 #0 SMP Thu Aug 26 00:00:00 MSD 2010 x86_64
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
Build Date: 30 May 2012  09:17:44PM

Current version of pixman: 0.24.0
    Before reporting problems, check wiki.x.org
    to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/usr/local/var/log/Xorg.0.log", Time: Tue Jun 19 00:27:56 2012
(==) Using config file: "/etc/X11/xorg.conf"
(EE) intel(0): [drm] Failed to open DRM device for pci:0000:00:02.0: No such file or directory
(EE) intel(0): Failed to become DRM master.
DRM_IOCTL_I915_GEM_APERTURE failed: Bad file descriptor
Assuming 131072kB available aperture size.
May lead to reduced performance or incorrect rendering.
get chip id failed: -1 [9]
param: 4, val: 0
(EE) intel(0): failed to get resources: Bad file descriptor
(EE) Screen(s) found, but none have a usable configuration.

Fatal server error:
no screens found

Please consult the The X.Org Foundation support
     at wiki.x.org
for help.
Please also check the log file at "/usr/local/var/log/Xorg.0.log" for additional information.

giving up.
xinit:  Connection refused (errno 111):  unable to connect to X server
xinit:  No such process (errno 3):  Server error.

Лог X

+ открыть спойлер

_XSERVTransSocketOpenCOTSServer: Unable to open socket for inet6
_XSERVTransOpen: transport open failed for inet6/localhost.localdomain:0
_XSERVTransMakeAllCOTSServerListeners: failed to open listener for inet6

This is a pre-release version of the X server from The X.Org Foundation.
It is not supported in any way.
Bugs may be filed in the bugzilla at bugs.freedesktop.org
Select the "xorg" product for bugs you find in this release.
Before reporting bugs in pre-release versions please check the
latest version in the X.Org Foundation git repository.
See wiki.x.org/wiki/GitPage for git access instructions.

X.Org X Server 1.6.99.903 (1.7.0 RC 3)
Release Date: 2009-9-28
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.18-238.19.1.el5 x86_64
Current Operating System: Linux localhost.localdomain 2.6.18-238.19.1.el5 #0 SMP Thu Aug 26 00:00:00 MSD 2010 x86_64
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
Build Date: 30 May 2012  09:17:44PM

Current version of pixman: 0.24.0
    Before reporting problems, check wiki.x.org
    to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/usr/local/var/log/Xorg.0.log", Time: Tue Jun 19 00:27:56 2012
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "Layout[all]"
(**) |-->Screen "Screen[0]" (0)
(**) |   |-->Monitor "Monitor[0]"
(**) |   |-->Device "Device[0]"
(**) |-->Input Device "Keyboard[0]"
(**) |-->Input Device "Mouse[1]"
(**) Option "AllowMouseOpenFail" "on"
(**) Option "Xinerama" "off"
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/lib64/X11/fonts/local" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/URW" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/PEX" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/latin2/misc" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/latin2/75dpi" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/latin2/100dpi" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/latin2/Type1" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/latin7/75dpi" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/baekmuk" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/japanese" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/kwintv" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/uni" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/CID" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/ucs/misc" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/ucs/75dpi" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/ucs/100dpi" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/hellas/misc" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/hellas/75dpi" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/hellas/100dpi" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/hellas/Type1" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/misc/sgi" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/lib64/X11/fonts/xtest" does not exist.
    Entry deleted from font path.
(WW) The directory "/opt/kde3/share/fonts" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/local/lib/X11/fonts/misc/" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/local/lib/X11/fonts/TTF/" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/local/lib/X11/fonts/OTF" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/local/lib/X11/fonts/Type1/" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/local/lib/X11/fonts/100dpi/" does not exist.
    Entry deleted from font path.
(WW) The directory "/usr/local/lib/X11/fonts/75dpi/" does not exist.
    Entry deleted from font path.
(**) FontPath set to:
    /usr/lib64/X11/fonts/misc:unscaled,
    /usr/lib64/X11/fonts/75dpi:unscaled,
    /usr/lib64/X11/fonts/100dpi:unscaled,
    /usr/lib64/X11/fonts/Type1,
    /usr/lib64/X11/fonts/Speedo,
    /usr/lib64/X11/fonts/cyrillic,
    /usr/lib64/X11/fonts/truetype
(==) ModulePath set to "/usr/local/lib/xorg/modules"
(WW) AllowEmptyInput is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
(WW) Disabling Keyboard[0]
(WW) Disabling Mouse[1]
(II) Loader magic: 0x7aee80
(II) Module ABI versions:
    X.Org ANSI C Emulation: 0.4
    X.Org Video Driver: 6.0
    X.Org XInput driver : 7.0
    X.Org Server Extension : 2.0
(--) using VT number 7

(--) PCI:*(0:0:2:0) 8086:a011:8086:a011 Intel Corporation N10 Family Integrated Graphics Controller rev 0, Mem @ 0xfea00000/524288, 0xd0000000/268435456, 0xfe900000/1048576, I/O @ 0x0000c080/8
(--) PCI: (0:0:2:1) 8086:a012:8086:a011 Intel Corporation N10 Family Integrated Graphics Controller rev 0, Mem @ 0xfe880000/524288
(II) Open ACPI successful (/var/run/acpid.socket)
(II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
(II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
(II) "glx" will be loaded. This was enabled by default and also specified in the config file.
(II) "dri" will be loaded. This was enabled by default and also specified in the config file.
(II) "dri2" will be loaded. This was enabled by default and also specified in the config file.
(II) LoadModule: "dri2"
(II) Loading /usr/local/lib/xorg/modules/extensions/libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
    compiled for 1.6.99.903, module version = 1.1.0
    ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "dbe"
(II) Loading /usr/local/lib/xorg/modules/extensions/libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
    compiled for 1.6.99.903, module version = 1.0.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/local/lib/xorg/modules/extensions/libglx.so
(II) Module glx: vendor="X.Org Foundation"
    compiled for 1.6.99.903, module version = 1.0.0
    ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "extmod"
(II) Loading /usr/local/lib/xorg/modules/extensions/libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
    compiled for 1.6.99.903, module version = 1.0.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dri"
(II) Loading /usr/local/lib/xorg/modules/extensions/libdri.so
(II) Module dri: vendor="X.Org Foundation"
    compiled for 1.6.99.903, module version = 1.0.0
    ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "intel"
(II) Loading /usr/local/lib/xorg/modules/drivers/intel_drv.so
(II) Module intel: vendor="X.Org Foundation"
    compiled for 1.6.99.903, module version = 2.17.0
    Module class: X.Org Video Driver
    ABI class: X.Org Video Driver, version 6.0
(II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
    i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G,
    E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
    965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
    4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,
    Sandybridge Desktop (GT1), Sandybridge Desktop (GT2),
    Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1),
    Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+),
    Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2),
    Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server
(II) Primary Device is: PCI 00@00:02:0
(WW) VGA arbiter: cannot open kernel arbiter, no multi-card support
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: Searching for BusID pci:0000:00:02.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card1
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card2
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card3
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card4
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card5
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card6
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card7
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card8
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card9
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card10
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card11
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card12
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card13
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card14
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card15
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card1
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card2
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card3
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card4
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card5
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card6
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card7
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card8
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card9
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card10
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card11
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card12
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card13
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card14
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card15
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
(EE) intel(0): [drm] Failed to open DRM device for pci:0000:00:02.0: No such file or directory
(EE) intel(0): Failed to become DRM master.
(**) intel(0): Depth 24, (--) framebuffer bpp 32
(==) intel(0): RGB weight 888
(==) intel(0): Default visual is TrueColor
(II) intel(0): Integrated Graphics Chipset: Intel(R) Pineview GM
(--) intel(0): Chipset: "Pineview GM"
(**) intel(0): Relaxed fencing disabled
(**) intel(0): Wait on SwapBuffers? enabled
(**) intel(0): Triple buffering? enabled
(**) intel(0): Framebuffer tiled
(**) intel(0): Pixmaps tiled
(**) intel(0): 3D buffers tiled
(**) intel(0): SwapBuffers wait enabled
(==) intel(0): video overlay key set to 0x101fe
(EE) intel(0): failed to get resources: Bad file descriptor
(II) UnloadModule: "intel"
(EE) Screen(s) found, but none have a usable configuration.

Fatal server error:
no screens found

Please consult the The X.Org Foundation support
     at wiki.x.org
for help.
Please also check the log file at "/usr/local/var/log/Xorg.0.log" for additional information.

4

мда... не заметил, что МСВС. Криокамера это... не стал бы отписываться т.к. не особо компетентен...

суть в том, что устройство /dev/dri/card0 не создаётся.
или ядро виновато или udev(или кто там занимается созданием устройств в /dev/ ?). В общем что-то из этого нужно посвежее. совсем свежее ядро я бы не стал пробовать, а вот из диапазона 2.6.{22,24,29} можно (цифры называл почти наугад).
ещё смущает, что нет BusID в Device в xorg.conf'е

95% процентов проблем находятся между клавиатурой и стулом.

5

udev я обновил, но это не помогает.
Ядро нельзя трогать, начальство не разрешает.

6 (19.06.2012 13:20:41 отредактировано yars)

А если попробовать написать/поправить правило udev, создающее нужное устройство? Вот тред, там про флешки, правда, но в качестве примера сойдет. Вот еще, статья на OpenNET, посвященная udev.

Истинный hotplug - это обычная электрическая розетка: воткнул - работает, и никаких драйверов.
Arch Linux/Xfce/Xiaomi Mi Notebook Pro 15.6 | Slackware64-current/Xfce/Lenovo G580

7

yars пишет:

А если попробовать написать/поправить правило udev, создающее нужное устройство? Вот тред, там про флешки, правда, но в качестве примера сойдет. Вот еще, статья на OpenNET, посвященная udev.

не уверен, что тут «ядерная» часть драйвера поддерживат dri... не говоря уже о том, поддерживает ли сам драйвер относительно новый чип...
как вариант - самому поколупаться и выдрать откуда-нить ядерный драйвер, но без больших плясок с бубном он не встанет...

95% процентов проблем находятся между клавиатурой и стулом.

8

Fat-Zer пишет:

без больших плясок с бубном он не встанет...

Тогда действительно, выходом с наименьшими трудозатратами было бы, естественно, обновление ядра, но раз начальство ТСа против, то других вариантов я не вижу.

Истинный hotplug - это обычная электрическая розетка: воткнул - работает, и никаких драйверов.
Arch Linux/Xfce/Xiaomi Mi Notebook Pro 15.6 | Slackware64-current/Xfce/Lenovo G580

9

Вот я и трясу щас бубен над исходниками, но пока мало толку, очень ну просто очень много ошибок.

10

Ребята, нужна помощь. МСВС поставил, но при работе не печается по русски, хотя вроде переключает. Пытаюсь сменить настройки сочетания клавиш, запрашивает разрешение на создание xorg.conf, соглашаюсь. перезагрузка - теперь мышь не работает. удаляю конф мышь работает. есть идеи?

11

cky29, покажите сам /etc/X11/xorg.conf, что в нём меняете.

cky29 пишет:

перезагрузка - теперь мышь не работает. удаляю конф мышь работает. есть идеи?

...и /var/log/Xorg.0.log для обоих случаев.

Был, был и весь вышел...

12

Можно вынести настройки в каталог /etc/X11/xorg.conf.d/ по-идее без xorg.conf должно работать.

История показывает, что во всем новом обычно кроется какой-то подвох.
Классическая ошибка, которую совершают проектировщики
абсолютно надежных систем, - недооценка изобретательности клинических идиотов.

13 (20.09.2012 09:46:10 отредактировано cky29)

Lupo Alberto пишет:

cky29, покажите сам /etc/X11/xorg.conf, что в нём меняете.

cky29 пишет:

перезагрузка - теперь мышь не работает. удаляю конф мышь работает. есть идеи?

...и /var/log/Xorg.0.log для обоих случаев.

ничего не меняю нигде. ламер в линухе, так что помогайте как сможете и доступным языком... )))

14

cky29 пишет:
Lupo Alberto пишет:

cky29, покажите сам /etc/X11/xorg.conf...и /var/log/Xorg.0.log для обоих случаев.

ничего не меняю нигде. ламер в линухе, так что помогайте как сможете и доступным языком... )))

Ну так показывайте же! Еще поищите по форуму, здесь много примеров xorg.conf, в том числе, выложенных мной.

Истинный hotplug - это обычная электрическая розетка: воткнул - работает, и никаких драйверов.
Arch Linux/Xfce/Xiaomi Mi Notebook Pro 15.6 | Slackware64-current/Xfce/Lenovo G580

15

yars пишет:
cky29 пишет:
Lupo Alberto пишет:

cky29, покажите сам /etc/X11/xorg.conf...и /var/log/Xorg.0.log для обоих случаев.

ничего не меняю нигде. ламер в линухе, так что помогайте как сможете и доступным языком... )))

Ну так показывайте же! Еще поищите по форуму, здесь много примеров xorg.conf, в том числе, выложенных мной.

+ Xorg.conf

Section "ServerLayout"
    Identifier     "X.org Configured"
    Screen      0  "Screen0" 0 0
    InputDevice    "Mouse0" "CorePointer"
    InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
    RgbPath      "/usr/share/X11/rgb"
    ModulePath   "/usr/lib/xorg/modules/updates"
    ModulePath   "/usr/lib/xorg/modules"
    FontPath     "catalogue:/etc/X11/fontpath.d"
    FontPath     "built-ins"
EndSection

Section "Module"
    Load  "GLcore"
    Load  "dbe"
    Load  "dri"
    Load  "extmod"
    Load  "glx"
    Load  "record"
    Load  "xtrap"
EndSection

Section "InputDevice"
    Identifier  "Keyboard0"
    Driver      "kbd"
    Option        "XkbLayout" "us,ru"
    Option        "XkbOptions" "grp:ctrl_shift_toggle"
EndSection

Section "InputDevice"
    Identifier  "Mouse0"
    Driver      "mouse"
    Option        "Protocol" "auto"
    Option        "Device" "/dev/input/mice"
    Option        "ZAxisMapping" "4 5 6 7"
EndSection

Section "Monitor"
    Identifier   "Monitor0"
    VendorName   "Monitor Vendor"
    ModelName    "Monitor Model"
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
        ### [arg]: arg optional
        #Option     "HWcursor"               # [<bool>]
        #Option     "Xinerama"               # [<bool>]
        #Option     "StaticXinerama"         # <str>
    Identifier  "Card0"
    Driver      "vmware"
    VendorName  "VMware Inc"
    BoardName   "[VMware SVGA II] PCI Display Adapter"
    BusID       "PCI:0:15:0"
EndSection

Section "Screen"
    Identifier "Screen0"
    Device     "Card0"
    Monitor    "Monitor0"
    SubSection "Display"
        Viewport   0 0
        Depth     1
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     4
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     8
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     15
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     16
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     24
    EndSubSection
EndSection

16

+ xorg.log

X.Org X Server 1.4.2
Release Date: 13 March 2008
X Protocol Version 11, Revision 0
Build Operating System: MCBC VNIINS
Current Operating System: Linux sobi 2.4.32-vniins42 #1 юФЧ бЧЗ 14 00:00:00 MSD 2008 i686
Build Date: 14 August 2008  12:00:52AM
Build ID: xorg-x11-server 7.3-117.1vniins9
    Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Thu Sep 20 08:49:56 2012
(EE) Unable to locate/open config file
(II) Loader magic: 0x81c23c0
(II) Module ABI versions:
    X.Org ANSI C Emulation: 0.3
    X.Org Video Driver: 2.0
    X.Org XInput driver : 2.0
    X.Org Server Extension : 0.3
    X.Org Font Renderer : 0.5
(II) Loader running on linux
(II) LoadModule: "pcidata"
(II) Loading /usr/lib/xorg/modules//libpcidata.so
(II) Module pcidata: vendor="X.Org Foundation"
    compiled for 1.4.2, module version = 1.0.0
    ABI class: X.Org Video Driver, version 2.0
(--) using VT number 7

(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 8086,7190 card 15ad,1976 rev 01 class 06,00,00 hdr 00
(II) PCI: 00:01:0: chip 8086,7191 card 0000,0000 rev 01 class 06,04,00 hdr 01
(II) PCI: 00:07:0: chip 8086,7110 card 15ad,1976 rev 08 class 06,01,00 hdr 80
(II) PCI: 00:07:1: chip 8086,7111 card 15ad,1976 rev 01 class 01,01,8a hdr 00
(II) PCI: 00:07:3: chip 8086,7113 card 15ad,1976 rev 08 class 06,80,00 hdr 80
(II) PCI: 00:07:7: chip 15ad,0740 card 15ad,0740 rev 10 class 08,80,00 hdr 00
(II) PCI: 00:0f:0: chip 15ad,0405 card 15ad,0405 rev 00 class 03,00,00 hdr 00
(II) PCI: 00:10:0: chip 104b,1040 card 104b,1040 rev 01 class 01,00,00 hdr 00
(II) PCI: 00:11:0: chip 15ad,0790 card 0000,0000 rev 02 class 06,04,01 hdr 01
(II) PCI: 00:15:0: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:15:1: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:15:2: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:15:3: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:15:4: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:15:5: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:15:6: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:15:7: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:16:0: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:16:1: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:16:2: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:16:3: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:16:4: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:16:5: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:16:6: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:16:7: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:17:0: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:17:1: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:17:2: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:17:3: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:17:4: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:17:5: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:17:6: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:17:7: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:18:0: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:18:1: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:18:2: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:18:3: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:18:4: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:18:5: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:18:6: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 00:18:7: chip 15ad,07a0 card 0000,0000 rev 01 class 06,04,00 hdr 81
(II) PCI: 02:00:0: chip 1022,2000 card 1022,2000 rev 10 class 02,00,00 hdr 00
(II) PCI: 02:01:0: chip 1274,1371 card 1274,1371 rev 02 class 04,01,00 hdr 00
(II) PCI: End of PCI scan
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,34), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
    [0] -1    0    0x00000000 - 0x0000ffff (0x10000) IXb
(II) Bus 0 non-prefetchable memory range:
    [0] -1    0    0x00000000 - 0xffffffff (0x0) MXb
(II) Bus 0 prefetchable memory range:
    [0] -1    0    0x00000000 - 0xffffffff (0x0) MXb
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x0004 (VGA_EN is cleared)
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:7:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(II) Subtractive PCI-to-PCI bridge:
(II) Bus 2: bridge is at (0:17:0), (0,2,2), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 2 I/O range:
    [0] -1    0    0x00002000 - 0x000020ff (0x100) IXb
    [1] -1    0    0x00002400 - 0x000024ff (0x100) IXb
    [2] -1    0    0x00002800 - 0x000028ff (0x100) IXb
    [3] -1    0    0x00002c00 - 0x00002cff (0x100) IXb
    [4] -1    0    0x00003000 - 0x000030ff (0x100) IXb
    [5] -1    0    0x00003400 - 0x000034ff (0x100) IXb
    [6] -1    0    0x00003800 - 0x000038ff (0x100) IXb
    [7] -1    0    0x00003c00 - 0x00003cff (0x100) IXb
(II) Bus 2 non-prefetchable memory range:
    [0] -1    0    0xc9900000 - 0xca3fffff (0xb00000) MXb
(II) Bus 2 prefetchable memory range:
    [0] -1    0    0xd8400000 - 0xd89fffff (0x600000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 3: bridge is at (0:21:0), (0,3,3), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 3 I/O range:
    [0] -1    0    0x00004000 - 0x000040ff (0x100) IXb
    [1] -1    0    0x00004400 - 0x000044ff (0x100) IXb
    [2] -1    0    0x00004800 - 0x000048ff (0x100) IXb
    [3] -1    0    0x00004c00 - 0x00004cff (0x100) IXb
(II) Bus 3 non-prefetchable memory range:
    [0] -1    0    0xca400000 - 0xca4fffff (0x100000) MXb
(II) Bus 3 prefetchable memory range:
    [0] -1    0    0xd8a00000 - 0xd8afffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 4: bridge is at (0:21:1), (0,4,4), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 4 I/O range:
    [0] -1    0    0x00008000 - 0x000080ff (0x100) IXb
    [1] -1    0    0x00008400 - 0x000084ff (0x100) IXb
    [2] -1    0    0x00008800 - 0x000088ff (0x100) IXb
    [3] -1    0    0x00008c00 - 0x00008cff (0x100) IXb
(II) Bus 4 non-prefetchable memory range:
    [0] -1    0    0xca800000 - 0xca8fffff (0x100000) MXb
(II) Bus 4 prefetchable memory range:
    [0] -1    0    0xd8e00000 - 0xd8efffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 5: bridge is at (0:21:2), (0,5,5), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 5 I/O range:
    [0] -1    0    0x0000c000 - 0x0000c0ff (0x100) IXb
    [1] -1    0    0x0000c400 - 0x0000c4ff (0x100) IXb
    [2] -1    0    0x0000c800 - 0x0000c8ff (0x100) IXb
    [3] -1    0    0x0000cc00 - 0x0000ccff (0x100) IXb
(II) Bus 5 non-prefetchable memory range:
    [0] -1    0    0xcac00000 - 0xcacfffff (0x100000) MXb
(II) Bus 5 prefetchable memory range:
    [0] -1    0    0xd9200000 - 0xd92fffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 6: bridge is at (0:21:3), (0,6,6), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 6 non-prefetchable memory range:
    [0] -1    0    0xcb000000 - 0xcb0fffff (0x100000) MXb
(II) Bus 6 prefetchable memory range:
    [0] -1    0    0xd9600000 - 0xd96fffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 7: bridge is at (0:21:4), (0,7,7), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 7 non-prefetchable memory range:
    [0] -1    0    0xcb400000 - 0xcb4fffff (0x100000) MXb
(II) Bus 7 prefetchable memory range:
    [0] -1    0    0xd9a00000 - 0xd9afffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 8: bridge is at (0:21:5), (0,8,8), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 8 non-prefetchable memory range:
    [0] -1    0    0xcb800000 - 0xcb8fffff (0x100000) MXb
(II) Bus 8 prefetchable memory range:
    [0] -1    0    0xd9e00000 - 0xd9efffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 9: bridge is at (0:21:6), (0,9,9), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 9 non-prefetchable memory range:
    [0] -1    0    0xcbc00000 - 0xcbcfffff (0x100000) MXb
(II) Bus 9 prefetchable memory range:
    [0] -1    0    0xda200000 - 0xda2fffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 10: bridge is at (0:21:7), (0,10,10), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 10 non-prefetchable memory range:
    [0] -1    0    0xcc000000 - 0xcc0fffff (0x100000) MXb
(II) Bus 10 prefetchable memory range:
    [0] -1    0    0xda600000 - 0xda6fffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 11: bridge is at (0:22:0), (0,11,11), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 11 I/O range:
    [0] -1    0    0x00005000 - 0x000050ff (0x100) IXb
    [1] -1    0    0x00005400 - 0x000054ff (0x100) IXb
    [2] -1    0    0x00005800 - 0x000058ff (0x100) IXb
    [3] -1    0    0x00005c00 - 0x00005cff (0x100) IXb
(II) Bus 11 non-prefetchable memory range:
    [0] -1    0    0xca500000 - 0xca5fffff (0x100000) MXb
(II) Bus 11 prefetchable memory range:
    [0] -1    0    0xd8b00000 - 0xd8bfffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 12: bridge is at (0:22:1), (0,12,12), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 12 I/O range:
    [0] -1    0    0x00009000 - 0x000090ff (0x100) IXb
    [1] -1    0    0x00009400 - 0x000094ff (0x100) IXb
    [2] -1    0    0x00009800 - 0x000098ff (0x100) IXb
    [3] -1    0    0x00009c00 - 0x00009cff (0x100) IXb
(II) Bus 12 non-prefetchable memory range:
    [0] -1    0    0xca900000 - 0xca9fffff (0x100000) MXb
(II) Bus 12 prefetchable memory range:
    [0] -1    0    0xd8f00000 - 0xd8ffffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 13: bridge is at (0:22:2), (0,13,13), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 13 I/O range:
    [0] -1    0    0x0000d000 - 0x0000d0ff (0x100) IXb
    [1] -1    0    0x0000d400 - 0x0000d4ff (0x100) IXb
    [2] -1    0    0x0000d800 - 0x0000d8ff (0x100) IXb
    [3] -1    0    0x0000dc00 - 0x0000dcff (0x100) IXb
(II) Bus 13 non-prefetchable memory range:
    [0] -1    0    0xcad00000 - 0xcadfffff (0x100000) MXb
(II) Bus 13 prefetchable memory range:
    [0] -1    0    0xd9300000 - 0xd93fffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 14: bridge is at (0:22:3), (0,14,14), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 14 non-prefetchable memory range:
    [0] -1    0    0xcb100000 - 0xcb1fffff (0x100000) MXb
(II) Bus 14 prefetchable memory range:
    [0] -1    0    0xd9700000 - 0xd97fffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 15: bridge is at (0:22:4), (0,15,15), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 15 non-prefetchable memory range:
    [0] -1    0    0xcb500000 - 0xcb5fffff (0x100000) MXb
(II) Bus 15 prefetchable memory range:
    [0] -1    0    0xd9b00000 - 0xd9bfffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 16: bridge is at (0:22:5), (0,16,16), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 16 non-prefetchable memory range:
    [0] -1    0    0xcb900000 - 0xcb9fffff (0x100000) MXb
(II) Bus 16 prefetchable memory range:
    [0] -1    0    0xd9f00000 - 0xd9ffffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 17: bridge is at (0:22:6), (0,17,17), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 17 non-prefetchable memory range:
    [0] -1    0    0xcbd00000 - 0xcbdfffff (0x100000) MXb
(II) Bus 17 prefetchable memory range:
    [0] -1    0    0xda300000 - 0xda3fffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 18: bridge is at (0:22:7), (0,18,18), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 18 non-prefetchable memory range:
    [0] -1    0    0xcc100000 - 0xcc1fffff (0x100000) MXb
(II) Bus 18 prefetchable memory range:
    [0] -1    0    0xda700000 - 0xda7fffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 19: bridge is at (0:23:0), (0,19,19), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 19 I/O range:
    [0] -1    0    0x00006000 - 0x000060ff (0x100) IXb
    [1] -1    0    0x00006400 - 0x000064ff (0x100) IXb
    [2] -1    0    0x00006800 - 0x000068ff (0x100) IXb
    [3] -1    0    0x00006c00 - 0x00006cff (0x100) IXb
(II) Bus 19 non-prefetchable memory range:
    [0] -1    0    0xca600000 - 0xca6fffff (0x100000) MXb
(II) Bus 19 prefetchable memory range:
    [0] -1    0    0xd8c00000 - 0xd8cfffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 20: bridge is at (0:23:1), (0,20,20), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 20 I/O range:
    [0] -1    0    0x0000a000 - 0x0000a0ff (0x100) IXb
    [1] -1    0    0x0000a400 - 0x0000a4ff (0x100) IXb
    [2] -1    0    0x0000a800 - 0x0000a8ff (0x100) IXb
    [3] -1    0    0x0000ac00 - 0x0000acff (0x100) IXb
(II) Bus 20 non-prefetchable memory range:
    [0] -1    0    0xcaa00000 - 0xcaafffff (0x100000) MXb
(II) Bus 20 prefetchable memory range:
    [0] -1    0    0xd9000000 - 0xd90fffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 21: bridge is at (0:23:2), (0,21,21), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 21 I/O range:
    [0] -1    0    0x0000e000 - 0x0000e0ff (0x100) IXb
    [1] -1    0    0x0000e400 - 0x0000e4ff (0x100) IXb
    [2] -1    0    0x0000e800 - 0x0000e8ff (0x100) IXb
    [3] -1    0    0x0000ec00 - 0x0000ecff (0x100) IXb
(II) Bus 21 non-prefetchable memory range:
    [0] -1    0    0xcae00000 - 0xcaefffff (0x100000) MXb
(II) Bus 21 prefetchable memory range:
    [0] -1    0    0xd9400000 - 0xd94fffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 22: bridge is at (0:23:3), (0,22,22), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 22 non-prefetchable memory range:
    [0] -1    0    0xcb200000 - 0xcb2fffff (0x100000) MXb
(II) Bus 22 prefetchable memory range:
    [0] -1    0    0xd9800000 - 0xd98fffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 23: bridge is at (0:23:4), (0,23,23), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 23 non-prefetchable memory range:
    [0] -1    0    0xcb600000 - 0xcb6fffff (0x100000) MXb
(II) Bus 23 prefetchable memory range:
    [0] -1    0    0xd9c00000 - 0xd9cfffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 24: bridge is at (0:23:5), (0,24,24), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 24 non-prefetchable memory range:
    [0] -1    0    0xcba00000 - 0xcbafffff (0x100000) MXb
(II) Bus 24 prefetchable memory range:
    [0] -1    0    0xda000000 - 0xda0fffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 25: bridge is at (0:23:6), (0,25,25), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 25 non-prefetchable memory range:
    [0] -1    0    0xcbe00000 - 0xcbefffff (0x100000) MXb
(II) Bus 25 prefetchable memory range:
    [0] -1    0    0xda400000 - 0xda4fffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 26: bridge is at (0:23:7), (0,26,26), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 26 non-prefetchable memory range:
    [0] -1    0    0xcc200000 - 0xcc2fffff (0x100000) MXb
(II) Bus 26 prefetchable memory range:
    [0] -1    0    0xda800000 - 0xda8fffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 27: bridge is at (0:24:0), (0,27,27), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 27 I/O range:
    [0] -1    0    0x00007000 - 0x000070ff (0x100) IXb
    [1] -1    0    0x00007400 - 0x000074ff (0x100) IXb
    [2] -1    0    0x00007800 - 0x000078ff (0x100) IXb
    [3] -1    0    0x00007c00 - 0x00007cff (0x100) IXb
(II) Bus 27 non-prefetchable memory range:
    [0] -1    0    0xca700000 - 0xca7fffff (0x100000) MXb
(II) Bus 27 prefetchable memory range:
    [0] -1    0    0xd8d00000 - 0xd8dfffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 28: bridge is at (0:24:1), (0,28,28), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 28 I/O range:
    [0] -1    0    0x0000b000 - 0x0000b0ff (0x100) IXb
    [1] -1    0    0x0000b400 - 0x0000b4ff (0x100) IXb
    [2] -1    0    0x0000b800 - 0x0000b8ff (0x100) IXb
    [3] -1    0    0x0000bc00 - 0x0000bcff (0x100) IXb
(II) Bus 28 non-prefetchable memory range:
    [0] -1    0    0xcab00000 - 0xcabfffff (0x100000) MXb
(II) Bus 28 prefetchable memory range:
    [0] -1    0    0xd9100000 - 0xd91fffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 29: bridge is at (0:24:2), (0,29,29), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 29 I/O range:
    [0] -1    0    0x0000f000 - 0x0000f0ff (0x100) IXb
    [1] -1    0    0x0000f400 - 0x0000f4ff (0x100) IXb
    [2] -1    0    0x0000f800 - 0x0000f8ff (0x100) IXb
    [3] -1    0    0x0000fc00 - 0x0000fcff (0x100) IXb
(II) Bus 29 non-prefetchable memory range:
    [0] -1    0    0xcaf00000 - 0xcaffffff (0x100000) MXb
(II) Bus 29 prefetchable memory range:
    [0] -1    0    0xd9500000 - 0xd95fffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 30: bridge is at (0:24:3), (0,30,30), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 30 non-prefetchable memory range:
    [0] -1    0    0xcb300000 - 0xcb3fffff (0x100000) MXb
(II) Bus 30 prefetchable memory range:
    [0] -1    0    0xd9900000 - 0xd99fffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 31: bridge is at (0:24:4), (0,31,31), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 31 non-prefetchable memory range:
    [0] -1    0    0xcb700000 - 0xcb7fffff (0x100000) MXb
(II) Bus 31 prefetchable memory range:
    [0] -1    0    0xd9d00000 - 0xd9dfffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 32: bridge is at (0:24:5), (0,32,32), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 32 non-prefetchable memory range:
    [0] -1    0    0xcbb00000 - 0xcbbfffff (0x100000) MXb
(II) Bus 32 prefetchable memory range:
    [0] -1    0    0xda100000 - 0xda1fffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 33: bridge is at (0:24:6), (0,33,33), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 33 non-prefetchable memory range:
    [0] -1    0    0xcbf00000 - 0xcbffffff (0x100000) MXb
(II) Bus 33 prefetchable memory range:
    [0] -1    0    0xda500000 - 0xda5fffff (0x100000) MXb
(II) PCI-to-PCI bridge:
(II) Bus 34: bridge is at (0:24:7), (0,34,34), BCTRL: 0x0004 (VGA_EN is cleared)
(II) Bus 34 non-prefetchable memory range:
    [0] -1    0    0xcc300000 - 0xcc3fffff (0x100000) MXb
(II) Bus 34 prefetchable memory range:
    [0] -1    0    0xda900000 - 0xda9fffff (0x100000) MXb
(--) PCI:*(0:15:0) VMware Inc [VMware SVGA II] PCI Display Adapter rev 0, Mem @ 0xd0000000/27, 0xc8800000/23, I/O @ 0x10f0/4
New driver is "vmware"
(==) Using default built-in configuration (55 lines)
(==) --- Start of built-in configuration ---
    Section "Module"
        Load    "extmod"
        Load    "dbe"
        Load    "glx"
        Load    "freetype"
        Load    "type1"
        Load    "record"
        Load    "dri"
    EndSection
    Section "Monitor"
        Identifier    "Builtin Default Monitor"
    EndSection
    Section "Device"
        Identifier    "Builtin Default vmware Device 0"
        Driver    "vmware"
    EndSection
    Section "Screen"
        Identifier    "Builtin Default vmware Screen 0"
        Device    "Builtin Default vmware Device 0"
        Monitor    "Builtin Default Monitor"
    EndSection
    Section "Device"
        Identifier    "Builtin Default fbdev Device 0"
        Driver    "fbdev"
    EndSection
    Section "Screen"
        Identifier    "Builtin Default fbdev Screen 0"
        Device    "Builtin Default fbdev Device 0"
        Monitor    "Builtin Default Monitor"
    EndSection
    Section "Device"
        Identifier    "Builtin Default vesa Device 0"
        Driver    "vesa"
    EndSection
    Section "Screen"
        Identifier    "Builtin Default vesa Screen 0"
        Device    "Builtin Default vesa Device 0"
        Monitor    "Builtin Default Monitor"
    EndSection
    Section "Device"
        Identifier    "Builtin Default vga Device 0"
        Driver    "vga"
    EndSection
    Section "Screen"
        Identifier    "Builtin Default vga Screen 0"
        Device    "Builtin Default vga Device 0"
        Monitor    "Builtin Default Monitor"
    EndSection
    Section "ServerLayout"
        Identifier    "Builtin Default Layout"
        Screen    "Builtin Default vmware Screen 0"
        Screen    "Builtin Default fbdev Screen 0"
        Screen    "Builtin Default vesa Screen 0"
        Screen    "Builtin Default vga Screen 0"
    EndSection
(==) --- End of built-in configuration ---
(==) ServerLayout "Builtin Default Layout"
(**) |-->Screen "Builtin Default vmware Screen 0" (0)
(**) |   |-->Monitor "Builtin Default Monitor"
(**) |   |-->Device "Builtin Default vmware Device 0"
(**) |-->Screen "Builtin Default fbdev Screen 0" (1)
(**) |   |-->Monitor "Builtin Default Monitor"
(**) |   |-->Device "Builtin Default fbdev Device 0"
(**) |-->Screen "Builtin Default vesa Screen 0" (2)
(**) |   |-->Monitor "Builtin Default Monitor"
(**) |   |-->Device "Builtin Default vesa Device 0"
(**) |-->Screen "Builtin Default vga Screen 0" (3)
(**) |   |-->Monitor "Builtin Default Monitor"
(**) |   |-->Device "Builtin Default vga Device 0"
(==) Automatically adding devices
(==) Automatically enabling devices
(==) No FontPath specified.  Using compiled-in default.
(==) FontPath set to:
    catalogue:/etc/X11/fontpath.d,
    built-ins
(==) RgbPath set to "/usr/share/X11/rgb"
(==) ModulePath set to "/usr/lib/xorg/modules/updates,/usr/lib/xorg/modules"
(==) |-->Input Device "<default pointer>"
(==) |-->Input Device "<default keyboard>"
(==) The core pointer device wasn't specified explicitly in the layout.
    Using the default mouse configuration.
(==) The core keyboard device wasn't specified explicitly in the layout.
    Using the default keyboard configuration.
(II) Open ACPI successful (/var/run/acpid.socket)
(II) Addressable bus resource ranges are
    [0] -1    0    0x00000000 - 0xffffffff (0x0) MXb
    [1] -1    0    0x00000000 - 0x0000ffff (0x10000) IXb
(II) OS-reported resource ranges:
    [0] -1    0    0x00100000 - 0x3fffffff (0x3ff00000) MXbE(B)
    [1] -1    0    0x000f0000 - 0x000fffff (0x10000) MXb
    [2] -1    0    0x000c0000 - 0x000effff (0x30000) MXb
    [3] -1    0    0x00000000 - 0x0009ffff (0xa0000) MXb
    [4] -1    0    0x0000ffff - 0x0000ffff (0x1) IXb
    [5] -1    0    0x00000000 - 0x000000ff (0x100) IXb
(II) Active PCI resource ranges:
    [0] -1    0    0xc8002000 - 0xc800201f (0x20) MXb
    [1] -1    0    0xc8000000 - 0xc8001fff (0x2000) MXb
    [2] -1    0    0xc8800000 - 0xc8ffffff (0x800000) MXb(B)
    [3] -1    0    0xd0000000 - 0xd7ffffff (0x8000000) MXb(B)
    [4] -1    0    0x00002080 - 0x000020bf (0x40) IXb
    [5] -1    0    0x00002000 - 0x0000207f (0x80) IXb
    [6] -1    0    0x000010c0 - 0x000010df (0x20) IXb
    [7] -1    0    0x00001080 - 0x000010bf (0x40) IXb
    [8] -1    0    0x000010e0 - 0x000010ef (0x10) IXb
    [9] -1    0    0x000010f0 - 0x000010ff (0x10) IXb(B)
(II) Active PCI resource ranges after removing overlaps:
    [0] -1    0    0xc8002000 - 0xc800201f (0x20) MXb
    [1] -1    0    0xc8000000 - 0xc8001fff (0x2000) MXb
    [2] -1    0    0xc8800000 - 0xc8ffffff (0x800000) MXb(B)
    [3] -1    0    0xd0000000 - 0xd7ffffff (0x8000000) MXb(B)
    [4] -1    0    0x00002080 - 0x000020bf (0x40) IXb
    [5] -1    0    0x00002000 - 0x0000207f (0x80) IXb
    [6] -1    0    0x000010c0 - 0x000010df (0x20) IXb
    [7] -1    0    0x00001080 - 0x000010bf (0x40) IXb
    [8] -1    0    0x000010e0 - 0x000010ef (0x10) IXb
    [9] -1    0    0x000010f0 - 0x000010ff (0x10) IXb(B)
(II) OS-reported resource ranges after removing overlaps with PCI:
    [0] -1    0    0x00100000 - 0x3fffffff (0x3ff00000) MXbE(B)
    [1] -1    0    0x000f0000 - 0x000fffff (0x10000) MXb
    [2] -1    0    0x000c0000 - 0x000effff (0x30000) MXb
    [3] -1    0    0x00000000 - 0x0009ffff (0xa0000) MXb
    [4] -1    0    0x0000ffff - 0x0000ffff (0x1) IXb
    [5] -1    0    0x00000000 - 0x000000ff (0x100) IXb
(II) All system resource ranges:
    [0] -1    0    0x00100000 - 0x3fffffff (0x3ff00000) MXbE(B)
    [1] -1    0    0x000f0000 - 0x000fffff (0x10000) MXb
    [2] -1    0    0x000c0000 - 0x000effff (0x30000) MXb
    [3] -1    0    0x00000000 - 0x0009ffff (0xa0000) MXb
    [4] -1    0    0xc8002000 - 0xc800201f (0x20) MXb
    [5] -1    0    0xc8000000 - 0xc8001fff (0x2000) MXb
    [6] -1    0    0xc8800000 - 0xc8ffffff (0x800000) MXb(B)
    [7] -1    0    0xd0000000 - 0xd7ffffff (0x8000000) MXb(B)
    [8] -1    0    0x0000ffff - 0x0000ffff (0x1) IXb
    [9] -1    0    0x00000000 - 0x000000ff (0x100) IXb
    [10] -1    0    0x00002080 - 0x000020bf (0x40) IXb
    [11] -1    0    0x00002000 - 0x0000207f (0x80) IXb
    [12] -1    0    0x000010c0 - 0x000010df (0x20) IXb
    [13] -1    0    0x00001080 - 0x000010bf (0x40) IXb
    [14] -1    0    0x000010e0 - 0x000010ef (0x10) IXb
    [15] -1    0    0x000010f0 - 0x000010ff (0x10) IXb(B)
(II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
(II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
(II) "glx" will be loaded. This was enabled by default and also specified in the config file.
(II) "freetype" will be loaded. This was enabled by default and also specified in the config file.
(II) "type1" will be loaded. This was enabled by default and also specified in the config file.
(II) "record" will be loaded. This was enabled by default and also specified in the config file.
(II) "dri" will be loaded. This was enabled by default and also specified in the config file.
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules//extensions/libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
    compiled for 1.4.2, module version = 1.0.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 0.3
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules//extensions/libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
    compiled for 1.4.2, module version = 1.0.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 0.3
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules//extensions/libglx.so
(II) Module glx: vendor="X.Org Foundation"
    compiled for 1.4.2, module version = 1.0.0
    ABI class: X.Org Server Extension, version 0.3
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "freetype"
(II) Loading /usr/lib/xorg/modules//fonts/libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
    compiled for 1.4.2, module version = 2.1.0
    Module class: X.Org Font Renderer
    ABI class: X.Org Font Renderer, version 0.5
(II) Loading font FreeType
(II) LoadModule: "type1"
(II) Loading /usr/lib/xorg/modules//fonts/libtype1.so
(II) Module type1: vendor="X.Org Foundation"
    compiled for 1.4.2, module version = 1.0.2
    Module class: X.Org Font Renderer
    ABI class: X.Org Font Renderer, version 0.5
(II) Loading font Type1
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules//extensions/librecord.so
(II) Module record: vendor="X.Org Foundation"
    compiled for 1.4.2, module version = 1.13.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 0.3
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules//extensions/libdri.so
(II) Module dri: vendor="X.Org Foundation"
    compiled for 1.4.2, module version = 1.0.0
    ABI class: X.Org Server Extension, version 0.3
(II) Loading extension XFree86-DRI
(II) LoadModule: "vmware"
(II) Loading /usr/lib/xorg/modules//drivers/vmware_drv.so
(II) Module vmware: vendor="X.Org Foundation"
    compiled for 1.4.2, module version = 10.16.3
    Module class: X.Org Video Driver
    ABI class: X.Org Video Driver, version 2.0
(II) LoadModule: "fbdev"
(II) Loading /usr/lib/xorg/modules//drivers/fbdev_drv.so
(II) Module fbdev: vendor="X.Org Foundation"
    compiled for 1.4.2, module version = 0.4.0
    ABI class: X.Org Video Driver, version 2.0
(II) LoadModule: "vesa"
(II) Loading /usr/lib/xorg/modules//drivers/vesa_drv.so
(II) Module vesa: vendor="X.Org Foundation"
    compiled for 1.4.2, module version = 1.3.0
    Module class: X.Org Video Driver
    ABI class: X.Org Video Driver, version 2.0
(II) LoadModule: "vga"
(II) Loading /usr/lib/xorg/modules//drivers/vga_drv.so
(II) Module vga: vendor="X.Org Foundation"
    compiled for 1.4.2, module version = 4.1.0
    Module class: X.Org Video Driver
    ABI class: X.Org Video Driver, version 2.0
(II) LoadModule: "mouse"
(II) Loading /usr/lib/xorg/modules//input/mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
    compiled for 1.4.2, module version = 1.3.0
    Module class: X.Org XInput Driver
    ABI class: X.Org XInput driver, version 2.0
(II) LoadModule: "kbd"
(II) Loading /usr/lib/xorg/modules//input/kbd_drv.so
(II) Module kbd: vendor="X.Org Foundation"
    compiled for 1.4.2, module version = 1.3.1
    Module class: X.Org XInput Driver
    ABI class: X.Org XInput driver, version 2.0
(II) VMWARE: driver for VMware SVGA: vmware0405, vmware0710
(II) FBDEV: driver for framebuffer: fbdev
(II) VESA: driver for VESA chipsets: vesa
(II) VGA: Generic VGA driver (version 4.1) for chipsets: generic
(II) Primary Device is: PCI 00:0f:0
(--) Assigning device section with no busID to primary device
(--) Chipset vmware0405 found
(II) resource ranges after xf86ClaimFixedResources() call:
    [0] 0    0    0x000b8000 - 0x000bffff (0x8000) MXb
    [1] 0    0    0x000b0000 - 0x000b7fff (0x8000) MXb
    [2] 0    0    0x000a0000 - 0x000affff (0x10000) MXb
    [3] -1    0    0x00100000 - 0x3fffffff (0x3ff00000) MXbE(B)
    [4] -1    0    0x000f0000 - 0x000fffff (0x10000) MXb
    [5] -1    0    0x000c0000 - 0x000effff (0x30000) MXb
    [6] -1    0    0x00000000 - 0x0009ffff (0xa0000) MXb
    [7] -1    0    0xc8002000 - 0xc800201f (0x20) MXb
    [8] -1    0    0xc8000000 - 0xc8001fff (0x2000) MXb
    [9] -1    0    0xc8800000 - 0xc8ffffff (0x800000) MXb(B)
    [10] -1    0    0xd0000000 - 0xd7ffffff (0x8000000) MXb(B)
    [11] 0    0    0x000003c0 - 0x000003df (0x20) IXb
    [12] 0    0    0x000003b0 - 0x000003bb (0xc) IXb
    [13] -1    0    0x0000ffff - 0x0000ffff (0x1) IXb
    [14] -1    0    0x00000000 - 0x000000ff (0x100) IXb
    [15] -1    0    0x00002080 - 0x000020bf (0x40) IXb
    [16] -1    0    0x00002000 - 0x0000207f (0x80) IXb
    [17] -1    0    0x000010c0 - 0x000010df (0x20) IXb
    [18] -1    0    0x00001080 - 0x000010bf (0x40) IXb
    [19] -1    0    0x000010e0 - 0x000010ef (0x10) IXb
    [20] -1    0    0x000010f0 - 0x000010ff (0x10) IXb(B)
(II) Loading sub module "fbdevhw"
(II) LoadModule: "fbdevhw"
(II) Loading /usr/lib/xorg/modules/linux//libfbdevhw.so
(II) Module fbdevhw: vendor="X.Org Foundation"
    compiled for 1.4.2, module version = 0.0.2
    ABI class: X.Org Video Driver, version 2.0
(EE) open /dev/fb0: No such device
(--) Assigning device section with no busID to primary device
(--) Chipset vesa found
(--) Assigning device section with no busID to primary device
(--) Chipset generic found
(II) resource ranges after probing:
    [0] 0    0    0x000b8000 - 0x000bffff (0x8000) MXb
    [1] 0    0    0x000b0000 - 0x000b7fff (0x8000) MXb
    [2] 0    0    0x000a0000 - 0x000affff (0x10000) MXb
    [3] -1    0    0x00100000 - 0x3fffffff (0x3ff00000) MXbE(B)
    [4] -1    0    0x000f0000 - 0x000fffff (0x10000) MXb
    [5] -1    0    0x000c0000 - 0x000effff (0x30000) MXb
    [6] -1    0    0x00000000 - 0x0009ffff (0xa0000) MXb
    [7] -1    0    0xc8002000 - 0xc800201f (0x20) MXb
    [8] -1    0    0xc8000000 - 0xc8001fff (0x2000) MXb
    [9] -1    0    0xc8800000 - 0xc8ffffff (0x800000) MXb(B)
    [10] -1    0    0xd0000000 - 0xd7ffffff (0x8000000) MXb(B)
    [11] 0    0    0x000003c0 - 0x000003df (0x20) IXb
    [12] 0    0    0x000003b0 - 0x000003bb (0xc) IXb
    [13] -1    0    0x0000ffff - 0x0000ffff (0x1) IXb
    [14] -1    0    0x00000000 - 0x000000ff (0x100) IXb
    [15] -1    0    0x00002080 - 0x000020bf (0x40) IXb
    [16] -1    0    0x00002000 - 0x0000207f (0x80) IXb
    [17] -1    0    0x000010c0 - 0x000010df (0x20) IXb
    [18] -1    0    0x00001080 - 0x000010bf (0x40) IXb
    [19] -1    0    0x000010e0 - 0x000010ef (0x10) IXb
    [20] -1    0    0x000010f0 - 0x000010ff (0x10) IXb(B)
(II) Setting vga for screen 0.
(--) VMWARE(0): VMware SVGA regs at (0x10f0, 0x10f1)
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
    compiled for 1.4.2, module version = 0.1.0
    ABI class: X.Org Video Driver, version 2.0
(--) VMWARE(0): caps:  0x00FF83E2
(--) VMWARE(0): depth: 24
(--) VMWARE(0): bpp:   32
(--) VMWARE(0): vram:  33554432
(--) VMWARE(0): pbase: 0xd0000000
(--) VMWARE(0): mwidt: 3840
(--) VMWARE(0): mheig: 1920
(II) VMWARE(0): Creating default Display subsection in Screen section
    "Builtin Default vmware Screen 0" for depth/fbbpp 24/32
(--) VMWARE(0): depth: 24
(--) VMWARE(0): bpp:   32
(--) VMWARE(0): w.red: 8
(--) VMWARE(0): w.grn: 8
(--) VMWARE(0): w.blu: 8
(--) VMWARE(0): vis:   4
(==) VMWARE(0): Depth 24, (==) framebuffer bpp 32
(==) VMWARE(0): RGB weight 888
(==) VMWARE(0): Default visual is TrueColor
(==) VMWARE(0): Using HW cursor
(==) VMWARE(0): Using gamma correction (1.0, 1.0, 1.0)
(II) VMWARE(0): Builtin Default Monitor: Using default hsync range of 31.50-37.90 kHz
(II) VMWARE(0): Builtin Default Monitor: Using default vrefresh range of 50.00-70.00 Hz
(WW) VMWARE(0): Unable to estimate virtual size
(II) VMWARE(0): Clock range:   0.00 to 400000.00 MHz
(II) VMWARE(0): Not using default mode "640x350" (vrefresh out of range)
(II) VMWARE(0): Not using default mode "320x175" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "640x400" (vrefresh out of range)
(II) VMWARE(0): Not using default mode "320x200" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "720x400" (vrefresh out of range)
(II) VMWARE(0): Not using default mode "360x200" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "640x480" (vrefresh out of range)
(II) VMWARE(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "640x480" (vrefresh out of range)
(II) VMWARE(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "640x480" (hsync out of range)
(II) VMWARE(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "800x600" (hsync out of range)
(II) VMWARE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "800x600" (hsync out of range)
(II) VMWARE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "800x600" (hsync out of range)
(II) VMWARE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1024x768" (hsync out of range)
(II) VMWARE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1024x768" (hsync out of range)
(II) VMWARE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1024x768" (hsync out of range)
(II) VMWARE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1024x768" (hsync out of range)
(II) VMWARE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1152x864" (hsync out of range)
(II) VMWARE(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1280x960" (hsync out of range)
(II) VMWARE(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1280x960" (hsync out of range)
(II) VMWARE(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1280x1024" (hsync out of range)
(II) VMWARE(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1280x1024" (hsync out of range)
(II) VMWARE(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1280x1024" (hsync out of range)
(II) VMWARE(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1600x1200" (hsync out of range)
(II) VMWARE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1600x1200" (hsync out of range)
(II) VMWARE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1600x1200" (hsync out of range)
(II) VMWARE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1600x1200" (hsync out of range)
(II) VMWARE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1600x1200" (hsync out of range)
(II) VMWARE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1792x1344" (hsync out of range)
(II) VMWARE(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1792x1344" (hsync out of range)
(II) VMWARE(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1856x1392" (hsync out of range)
(II) VMWARE(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1856x1392" (hsync out of range)
(II) VMWARE(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1920x1440" (hsync out of range)
(II) VMWARE(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1920x1440" (hsync out of range)
(II) VMWARE(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "832x624" (hsync out of range)
(II) VMWARE(0): Not using default mode "416x312" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1152x768" (hsync out of range)
(II) VMWARE(0): Not using default mode "576x384" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1152x864" (hsync out of range)
(II) VMWARE(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1152x864" (hsync out of range)
(II) VMWARE(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1152x864" (hsync out of range)
(II) VMWARE(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1152x864" (hsync out of range)
(II) VMWARE(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1152x864" (hsync out of range)
(II) VMWARE(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1152x864" (hsync out of range)
(II) VMWARE(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1280x720" (hsync out of range)
(II) VMWARE(0): Not using default mode "640x360" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1280x720" (hsync out of range)
(II) VMWARE(0): Not using default mode "640x360" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1280x720" (hsync out of range)
(II) VMWARE(0): Not using default mode "640x360" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1280x720" (hsync out of range)
(II) VMWARE(0): Not using default mode "640x360" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1280x800" (hsync out of range)
(II) VMWARE(0): Not using default mode "640x400" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1280x800" (hsync out of range)
(II) VMWARE(0): Not using default mode "640x400" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1280x800" (hsync out of range)
(II) VMWARE(0): Not using default mode "640x400" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1280x800" (hsync out of range)
(II) VMWARE(0): Not using default mode "640x400" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1280x768" (hsync out of range)
(II) VMWARE(0): Not using default mode "640x384" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1280x768" (hsync out of range)
(II) VMWARE(0): Not using default mode "640x384" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1280x768" (hsync out of range)
(II) VMWARE(0): Not using default mode "640x384" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1280x768" (hsync out of range)
(II) VMWARE(0): Not using default mode "640x384" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1360x768" (hsync out of range)
(II) VMWARE(0): Not using default mode "680x384" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1360x768" (hsync out of range)
(II) VMWARE(0): Not using default mode "680x384" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1400x1050" (hsync out of range)
(II) VMWARE(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1400x1050" (hsync out of range)
(II) VMWARE(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1400x1050" (hsync out of range)
(II) VMWARE(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1400x1050" (hsync out of range)
(II) VMWARE(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1400x1050" (hsync out of range)
(II) VMWARE(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1400x1050" (hsync out of range)
(II) VMWARE(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1440x900" (hsync out of range)
(II) VMWARE(0): Not using default mode "720x450" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1600x1024" (hsync out of range)
(II) VMWARE(0): Not using default mode "800x512" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1680x1050" (hsync out of range)
(II) VMWARE(0): Not using default mode "840x525" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1680x1050" (hsync out of range)
(II) VMWARE(0): Not using default mode "840x525" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1680x1050" (hsync out of range)
(II) VMWARE(0): Not using default mode "840x525" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1680x1050" (hsync out of range)
(II) VMWARE(0): Not using default mode "840x525" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1680x1050" (hsync out of range)
(II) VMWARE(0): Not using default mode "840x525" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1920x1080" (hsync out of range)
(II) VMWARE(0): Not using default mode "960x540" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1920x1200" (hsync out of range)
(II) VMWARE(0): Not using default mode "960x600" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "1920x1440" (hsync out of range)
(II) VMWARE(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "2048x1536" (hsync out of range)
(II) VMWARE(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "2048x1536" (hsync out of range)
(II) VMWARE(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) VMWARE(0): Not using default mode "2048x1536" (hsync out of range)
(II) VMWARE(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(--) VMWARE(0): Virtual size is 800x600 (pitch 800)
(**) VMWARE(0): *Default mode "800x600": 40.0 MHz, 37.9 kHz, 60.3 Hz
(II) VMWARE(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(**) VMWARE(0): *Default mode "800x600": 36.0 MHz, 35.2 kHz, 56.2 Hz
(II) VMWARE(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
(**) VMWARE(0): *Default mode "640x480": 25.2 MHz, 31.5 kHz, 59.9 Hz
(II) VMWARE(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(==) VMWARE(0): DPI set to (96, 96)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
    compiled for 1.4.2, module version = 1.0.0
    ABI class: X.Org ANSI C Emulation, version 0.3
(II) Loading sub module "shadowfb"
(II) LoadModule: "shadowfb"
(II) Loading /usr/lib/xorg/modules//libshadowfb.so
(II) Module shadowfb: vendor="X.Org Foundation"
    compiled for 1.4.2, module version = 1.0.0
    ABI class: X.Org ANSI C Emulation, version 0.3
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"(II) Module "ramdac" already built-in
(II) UnloadModule: "fbdev"
(II) Unloading /usr/lib/xorg/modules//drivers/fbdev_drv.so
(II) UnloadModule: "fbdevhw"
(II) Unloading /usr/lib/xorg/modules/linux//libfbdevhw.so
(II) UnloadModule: "vesa"
(II) Unloading /usr/lib/xorg/modules//drivers/vesa_drv.so
(II) UnloadModule: "vga"
(II) Unloading /usr/lib/xorg/modules//drivers/vga_drv.so
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC?  No, I don't.
(II) resource ranges after preInit:
    [0] 0    0    0x000b8000 - 0x000bffff (0x8000) MXb
    [1] 0    0    0x000b0000 - 0x000b7fff (0x8000) MXb
    [2] 0    0    0x000a0000 - 0x000affff (0x10000) MXb
    [3] -1    0    0x00100000 - 0x3fffffff (0x3ff00000) MXbE(B)
    [4] -1    0    0x000f0000 - 0x000fffff (0x10000) MXb
    [5] -1    0    0x000c0000 - 0x000effff (0x30000) MXb
    [6] -1    0    0x00000000 - 0x0009ffff (0xa0000) MXb
    [7] -1    0    0xc8002000 - 0xc800201f (0x20) MXb
    [8] -1    0    0xc8000000 - 0xc8001fff (0x2000) MXb
    [9] -1    0    0xc8800000 - 0xc8ffffff (0x800000) MXb(B)
    [10] -1    0    0xd0000000 - 0xd7ffffff (0x8000000) MXb(B)
    [11] 0    0    0x000003c0 - 0x000003df (0x20) IXb
    [12] 0    0    0x000003b0 - 0x000003bb (0xc) IXb
    [13] -1    0    0x0000ffff - 0x0000ffff (0x1) IXb
    [14] -1    0    0x00000000 - 0x000000ff (0x100) IXb
    [15] -1    0    0x00002080 - 0x000020bf (0x40) IXb
    [16] -1    0    0x00002000 - 0x0000207f (0x80) IXb
    [17] -1    0    0x000010c0 - 0x000010df (0x20) IXb
    [18] -1    0    0x00001080 - 0x000010bf (0x40) IXb
    [19] -1    0    0x000010e0 - 0x000010ef (0x10) IXb
    [20] -1    0    0x000010f0 - 0x000010ff (0x10) IXb(B)
(II) VMWARE(0): Initialized VMWARE_CTRL extension version 0.2
(II) VMWARE(0): Initialized VMware Xinerama extension.
(II) VMWARE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(==) VMWARE(0): Write-combining range (0xd0000000,0x2000000)
(==) VMWARE(0): Backing store disabled
(==) VMWARE(0): Silken mouse enabled
(II) VMWARE(0): Initialized VMware Xv extension successfully.
(==) RandR enabled
(II) Setting vga for screen 0.
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XAccessControlExtension
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension SEMCBC
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(II) AIGLX: Screen 0 is not DRI capable
(II) Loading sub module "GLcore"
(II) LoadModule: "GLcore"
(II) Loading /usr/lib/xorg/modules//extensions/libGLcore.so
(II) Module GLcore: vendor="X.Org Foundation"
    compiled for 1.4.2, module version = 1.0.0
    ABI class: X.Org Server Extension, version 0.3
(II) GLX: Initialized MESA-PROXY GL provider for screen 0
(WW) <default pointer>: No Device specified, looking for one...
(II) <default pointer>: Setting Device option to "/dev/psaux"
(--) <default pointer>: Device: "/dev/psaux"
(==) <default pointer>: Protocol: "Auto"
(**) Option "CorePointer"
(**) <default pointer>: always reports core events
(==) <default pointer>: Emulate3Buttons, Emulate3Timeout: 50
(**) <default pointer>: ZAxisMapping: buttons 4 and 5
(**) <default pointer>: Buttons: 9
(**) <default pointer>: Sensitivity: 1
(**) Option "CoreKeyboard"
(**) <default keyboard>: always reports core events
(**) Option "Protocol" "standard"
(**) <default keyboard>: Protocol: standard
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xorg"
(**) <default keyboard>: XkbRules: "xorg"
(**) Option "XkbModel" "pc105"
(**) <default keyboard>: XkbModel: "pc105"
(**) Option "XkbLayout" "us"
(**) <default keyboard>: XkbLayout: "us"
(**) Option "CustomKeycodes" "off"
(**) <default keyboard>: CustomKeycodes disabled
(II) evaluating device (<default keyboard>)
(II) XINPUT: Adding extended input device "<default keyboard>" (type: KEYBOARD)
(II) evaluating device (<default pointer>)
(II) XINPUT: Adding extended input device "<default pointer>" (type: MOUSE)
(--) <default pointer>: PnP-detected protocol: "ImPS/2"
(II) <default pointer>: ps2EnableDataReporting: succeeded
Could not init font path element built-ins, removing from list!
(EE) Error compiling keymap (server-0)
(EE) XKB: Couldn't compile keymap
Warning: LookupWindow()/SecurityLookupWindow() are deprecated.  Please convert your driver/module to use dixLookupWindow().

17

по-прежнему ничего. взял xorg.conf с форума - описание клавы и мыши, startx не запустил мне стол даже.

18 (20.09.2012 14:19:27 отредактировано yars)

Так не весь файл нужно брать, а только то, что относится к клавиатуре. Какой именно файл вы взяли? Между прочим, вам всего одну строчку нужно дописать-поправить. Смотрите

diff -c ./ваш_файл ./файл_с_форума

ab А если серьезно, то это

Option "XkbVariant" ",winkeys"

ps.

+ открыть спойлер

на какие только ухищрения народ не идет, лишь бы мозг не включать (каюсь, грешен ab )

Истинный hotplug - это обычная электрическая розетка: воткнул - работает, и никаких драйверов.
Arch Linux/Xfce/Xiaomi Mi Notebook Pro 15.6 | Slackware64-current/Xfce/Lenovo G580

19

yars пишет:

Так не весь файл нужно брать, а только то, что относится к клавиатуре. Какой именно файл вы взяли? Между прочим, вам всего одну строчку нужно дописать-поправить. Смотрите

diff -c ./ваш_файл ./файл_с_форума

ab А если серьезно, то это

Option "XkbVariant" ",winkeys"

все, пишет по-русски, спасибо. Проблема 2 - мышь после перезагрузки не пашет. В конфе только строку добавил, ничего не трогал больше.
P.S.

+ открыть спойлер

Здесь каяться думаю нет смысла, нужно в церковь к батюшке ))) (все мы грешны в разной степени)

20

Покажите содержимое каталога /etc/X11/xorg.conf.d, если он есть.  В Slackware, например, за настройку клавиатуры отвечает файл /etc/X11/xorg.conf.d/90-keyboard-layout.conf. Но это "дробление" монолитного xorg.conf появилось только в новых версиях иксов. Кроме того, по умолчанию, указанного выше файла нет, его нужно создать.

Истинный hotplug - это обычная электрическая розетка: воткнул - работает, и никаких драйверов.
Arch Linux/Xfce/Xiaomi Mi Notebook Pro 15.6 | Slackware64-current/Xfce/Lenovo G580

21

yars пишет:

Покажите содержимое каталога /etc/X11/xorg.conf.d, если он есть.  В Slackware, например, за настройку клавиатуры отвечает файл /etc/X11/xorg.conf.d/90-keyboard-layout.conf. Но это "дробление" монолитного xorg.conf появилось только в новых версиях иксов. Кроме того, по умолчанию, указанного выше файла нет, его нужно создать.

его в моей мсвс его нету. как создать? какое содержимое должно быть? голова уж кругом...

22

cky29 пишет:

его в моей мсвс его нету. как создать

тыц
Но вам этого не нужно, ибо

cky29 пишет:
X.Org X Server 1.4.2
Release Date: 13 March 2008
X Protocol Version 11, Revision 0

А у меня

X.Org X Server 1.12.3
Release Date: 2012-07-09
X Protocol Version 11, Revision 0

Так что попробуйте закомментировать (поставить # в начале строки) все, что не относится к клавиатуре.

Section "InputDevice"
    Identifier  "Keyboard0"
    Driver      "kbd"
    Option        "XkbLayout" "us,ru"
    Option        "XkbVariant" ",winkeys"
    Option        "XkbOptions" "grp:ctrl_shift_toggle"
EndSection

Вот так должна выглядеть секция клавиатуры в xorg.conf.

Истинный hotplug - это обычная электрическая розетка: воткнул - работает, и никаких драйверов.
Arch Linux/Xfce/Xiaomi Mi Notebook Pro 15.6 | Slackware64-current/Xfce/Lenovo G580

23

короче, про клаву так и написано. закомментил - фатал ерор при запуске - вернул. мне мышь важна, только с ней траблы. помогите пож-ста еще мыслями... знаю уж надоел всем

24 (21.09.2012 21:13:13 отредактировано yars)

cky29 пишет:

запрашивает разрешение на создание xorg.conf

Это оригинальный файл, который создается?

+ открыть спойлер
Section "ServerLayout"
    Identifier     "X.org Configured"
    Screen      0  "Screen0" 0 0
    InputDevice    "Mouse0" "CorePointer"
    InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
    RgbPath      "/usr/share/X11/rgb"
    ModulePath   "/usr/lib/xorg/modules/updates"
    ModulePath   "/usr/lib/xorg/modules"
    FontPath     "catalogue:/etc/X11/fontpath.d"
    FontPath     "built-ins"
EndSection

Section "Module"
    Load  "GLcore"
    Load  "dbe"
    Load  "dri"
    Load  "extmod"
    Load  "glx"
    Load  "record"
    Load  "xtrap"
EndSection

Section "InputDevice"
    Identifier  "Keyboard0"
    Driver      "kbd"
    Option        "XkbLayout" "us,ru"
    Option        "XkbOptions" "grp:ctrl_shift_toggle"
EndSection

Section "InputDevice"
    Identifier  "Mouse0"
    Driver      "mouse"
    Option        "Protocol" "auto"
    Option        "Device" "/dev/input/mice"
    Option        "ZAxisMapping" "4 5 6 7"
EndSection

Section "Monitor"
    Identifier   "Monitor0"
    VendorName   "Monitor Vendor"
    ModelName    "Monitor Model"
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
        ### [arg]: arg optional
        #Option     "HWcursor"               # [<bool>]
        #Option     "Xinerama"               # [<bool>]
        #Option     "StaticXinerama"         # <str>
    Identifier  "Card0"
    Driver      "vmware"
    VendorName  "VMware Inc"
    BoardName   "[VMware SVGA II] PCI Display Adapter"
    BusID       "PCI:0:15:0"
EndSection

Section "Screen"
    Identifier "Screen0"
    Device     "Card0"
    Monitor    "Monitor0"
    SubSection "Display"
        Viewport   0 0
        Depth     1
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     4
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     8
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     15
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     16
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     24
    EndSubSection
EndSection

Если так, то выполните:

cp /etc/X11/xorg.conf /etc/X11/xorg.conf.old

и создайте новый файл с таким содержимым:

Section "ServerLayout"
    Identifier     "X.org Configured"
    Screen      0  "Screen0" 0 0
    InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
    RgbPath      "/usr/share/X11/rgb"
    ModulePath   "/usr/lib/xorg/modules/updates"
    ModulePath   "/usr/lib/xorg/modules"
    FontPath     "catalogue:/etc/X11/fontpath.d"
    FontPath     "built-ins"
EndSection

Section "Module"
    Load  "GLcore"
    Load  "dbe"
    Load  "dri"
    Load  "extmod"
    Load  "glx"
    Load  "record"
    Load  "xtrap"
EndSection

Section "InputDevice"
    Identifier  "Keyboard0"
    Driver      "kbd"
    Option        "XkbLayout" "us,ru"
    Option        "XkbVariant" ",winkeys"
    Option        "XkbOptions" "grp:ctrl_shift_toggle"
EndSection

Section "Monitor"
    Identifier   "Monitor0"
    VendorName   "Monitor Vendor"
    ModelName    "Monitor Model"
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
        ### [arg]: arg optional
        #Option     "HWcursor"               # [<bool>]
        #Option     "Xinerama"               # [<bool>]
        #Option     "StaticXinerama"         # <str>
    Identifier  "Card0"
    Driver      "vmware"
    VendorName  "VMware Inc"
    BoardName   "[VMware SVGA II] PCI Display Adapter"
    BusID       "PCI:0:15:0"
EndSection

Section "Screen"
    Identifier "Screen0"
    Device     "Card0"
    Monitor    "Monitor0"
    SubSection "Display"
        Viewport   0 0
        Depth     1
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     4
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     8
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     15
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     16
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     24
    EndSubSection
EndSection

Если мышь не работает, значит, некорректна секция Device, связанная с мышью.

Истинный hotplug - это обычная электрическая розетка: воткнул - работает, и никаких драйверов.
Arch Linux/Xfce/Xiaomi Mi Notebook Pro 15.6 | Slackware64-current/Xfce/Lenovo G580

25

В общем спасибо за помощь. проблему решил тупо поменяв настройки мыши через меню

26

В общем еще вопрос возник - как увеличить разрешение (стоит мсвс у меня на  vmware), в свойствах самой вирт машины для данной ОС смена недоступна (затенена). пытаюсь через систему в настройках, просит перезагрузиться, но потом все равно квадрат в центре экрана, хотя пишет что 1024*768

27

жаль, тишина

28

Переезжайте на VirtualBox. Тут WMware практически никто не пользуется ab

Истинный hotplug - это обычная электрическая розетка: воткнул - работает, и никаких драйверов.
Arch Linux/Xfce/Xiaomi Mi Notebook Pro 15.6 | Slackware64-current/Xfce/Lenovo G580

29

ну вроде разобрался. пока все поднято на вмваре, юзаю ее. прислушаюсь к совету. спасибо

30

Еще и еще вопрос. Ставлю уже на реальную машину, не видит винт. в биосе стоит ИДЕ режим, понимаю что нет дров на мой контроллер сата, как подпихнуть, как решить??? Очень надо, сроки